1. Introduction
This manual provides essential information for the proper use, installation, and maintenance of the Lampa 69996 Micro Blade Fuses. These fuses are designed to protect electrical circuits from overcurrent conditions, preventing damage to components and wiring. Please read this manual thoroughly before installation and use.
2. Product Overview
The Lampa 69996 set contains 100 micro blade fuses, each rated at 15 Amperes. These fuses are suitable for 12V and 32V DC automotive and similar low-voltage electrical systems. They are designed for single-use overcurrent protection, meaning they will blow and break the circuit when an excessive current flows through them, safeguarding your equipment.
Image 1: A clear plastic box containing 100 Lampa 69996 Micro Blade Fuses, each rated at 15 Amperes. The label on the box indicates "Automotive Micro Plug-in Fuses" and "Voltage Rating: MAX 32V DC".
3. Setup and Installation
Installing a micro blade fuse requires careful attention to safety and correct amperage matching. Always ensure the power to the circuit is off before handling fuses.
- Safety First: Disconnect the power source to the circuit where the fuse will be installed. This typically involves turning off the vehicle's ignition and disconnecting the battery if working on primary circuits.
- Identify the Fuse Holder: Locate the fuse box or inline fuse holder for the circuit requiring protection.
- Determine Correct Amperage: Always replace a fuse with one of the exact same amperage rating as specified by the equipment or vehicle manufacturer. Using a fuse with a higher amperage rating can lead to severe electrical damage or fire. The Lampa 69996 fuses are rated at 15A.
- Insert the Fuse: Gently push the new micro blade fuse into the designated slots in the fuse holder until it is firmly seated. Do not force it.
- Restore Power: Once the fuse is securely in place, reconnect the power source and test the circuit.
Warning: Never use a fuse with a higher amperage rating than specified. This can cause serious damage to your electrical system and pose a fire hazard.
Image 2: A close-up view of a single Lampa 69996 micro blade fuse. It is blue, indicating a 15 Ampere rating, with two metal prongs for insertion into a fuse holder.
4. Operating Instructions
Lampa micro blade fuses operate passively to protect electrical circuits. When the current flowing through a circuit exceeds the fuse's rated amperage (in this case, 15A), the metallic strip inside the fuse melts, breaking the circuit and preventing further current flow. This action protects connected devices and wiring from damage due to overcurrents or short circuits.
- Fuses are designed for single use. Once a fuse blows, it must be replaced.
- Always replace a blown fuse with a new fuse of the identical amperage rating.
5. Maintenance
Micro blade fuses generally require minimal maintenance. However, periodic inspection can help ensure the integrity of your electrical system.
- Visual Inspection: Periodically check fuses in critical circuits for any signs of damage, discoloration, or loose connections.
- Storage: Store spare fuses in a dry, cool place, away from direct sunlight and extreme temperatures, to maintain their integrity.
- Cleaning: Ensure fuse holders are clean and free of corrosion to maintain good electrical contact.
6. Troubleshooting
The primary troubleshooting scenario for fuses involves a circuit that has stopped functioning.
- Symptom: An electrical component or circuit is not working.
- Diagnosis:
- Locate the fuse associated with the non-functional circuit.
- Visually inspect the fuse. A blown fuse will typically have a broken or melted wire inside the transparent casing.
- If visual inspection is difficult, use a multimeter to check for continuity across the fuse terminals. A blown fuse will show no continuity.
- Solution:
- Before replacing, try to identify the cause of the overcurrent (e.g., short circuit, faulty component, overloaded circuit). Address the underlying issue if possible to prevent immediate re-blowing of the new fuse.
- Replace the blown fuse with a new Lampa 69996 15A micro blade fuse. Ensure the replacement fuse has the exact same amperage rating.
Important: If fuses continue to blow after replacement, consult a qualified electrician or automotive technician. Do not repeatedly replace fuses without addressing the root cause.
7. Specifications
| Attribute | Detail |
|---|---|
| Brand | Lampa |
| Model Number | 69996 |
| Amperage Rating | 15 Amperes (15A) |
| Voltage Rating | Max 32V DC (12V/32V compatible) |
| Quantity | 100 pieces |
| Fuse Type | Micro Blade Fuse |
| Item Weight | 80 grams |
| Product Dimensions (L x W x H) | 25 x 60 x 60 mm (approx. 2.5 x 6 x 6 cm) |
| GTIN (Global Trade Item Number) | 08000692699966 |
| ASIN | B01N5LA50E |
8. Warranty and Support
For warranty information and customer support regarding your Lampa 69996 Micro Blade Fuses, please refer to the documentation provided at the point of purchase or contact the retailer/manufacturer directly. Specific warranty terms may vary depending on your region and the seller.
For general inquiries or technical assistance, you may visit the official Lampa website or contact their customer service department.
