1. Introduction
Thank you for purchasing the Bunker Hill Security Battery Operated LED Motion Sensor Light. This device is designed to provide convenient, automatic illumination in indoor areas, enhancing security and visibility. Its motion-sensing capabilities ensure light is provided only when needed, conserving battery life. Please read this manual thoroughly before installation and operation to ensure proper use and longevity of your product.
2. Safety Information
- Indoor Use Only: This product is designed for indoor use. Do not expose it to rain, moisture, or extreme temperatures.
- Battery Safety: Use only the specified type and size of batteries. Ensure correct polarity (+/-) when inserting batteries. Do not mix old and new batteries, or different types of batteries. Remove batteries if the device will not be used for an extended period. Dispose of used batteries responsibly according to local regulations.
- Mounting: Ensure the mounting surface is stable and can support the weight of the light.
- Cleaning: Do not use abrasive cleaners or solvents. Clean with a soft, dry cloth.
- Disassembly: Do not attempt to disassemble or modify the light. This will void the warranty and may cause damage or injury.
3. Package Contents
Please check the package for the following items:
- 1 x Battery Operated LED Motion Sensor Light Unit
- 1 x Remote Control
- Mounting Hardware (screws/anchors, if applicable)
- User Manual (this document)
Image 1: Front view of the Bunker Hill Security Battery Operated LED Motion Sensor Light. The unit is white with a blue translucent top housing the LED, and a rectangular motion sensor window on the front face.
4. Setup and Installation
4.1 Battery Installation
This device requires batteries for operation (batteries are not included). Locate the battery compartment, typically on the back or bottom of the unit. Insert the required number and type of batteries (e.g., AA, AAA, C, D – check the compartment for specific markings) ensuring correct polarity (+ and -). Close the battery compartment securely.
4.2 Mounting
The light is designed for wall mounting. Choose an indoor location where the motion sensor will have an unobstructed view of the area you wish to monitor. Avoid placing it near heat sources, direct sunlight, or areas with strong air currents, as these can interfere with sensor performance.
- Mark the desired mounting position on the wall.
- Drill pilot holes if necessary, using a drill bit appropriate for your wall material and the provided mounting hardware.
- Insert wall anchors if required.
- Secure the light unit to the wall using the provided screws. Ensure it is firmly attached.
5. Operation
Once batteries are installed and the unit is mounted, the motion sensor light is ready for operation.
- Automatic Activation: The light will automatically turn on when motion is detected within its sensing range in a dark environment.
- Automatic Deactivation: After a period of no motion detection, the light will automatically turn off to conserve battery power. The duration the light stays on may vary based on the model.
- Remote Control: Use the included remote control to manually turn the light on/off or adjust settings if available (e.g., brightness, duration, sensitivity). Refer to the remote control's specific markings for its functions.
6. Maintenance
- Battery Replacement: When the light dims or fails to activate, it is time to replace the batteries. Follow the battery installation steps (Section 4.1).
- Cleaning: Periodically wipe the light and sensor window with a soft, dry, lint-free cloth to remove dust and dirt. Do not use liquid cleaners or sprays directly on the unit.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | Dead or incorrectly installed batteries. | Replace batteries, ensuring correct polarity. |
| Insufficient darkness for sensor activation. | Ensure the area is dark enough for the light sensor to activate. | |
| Motion sensor obstructed or dirty. | Clear any obstructions from the sensor window and clean it. | |
| Light stays on constantly. | Continuous motion detected. | Ensure no continuous motion is within the sensor's range. Reposition the light if necessary. |
| Sensor malfunction. | Remove batteries for a few minutes, then reinsert to reset the unit. If problem persists, contact support. |
8. Specifications
- Model: 0015817
- Brand: Bunker Hill Security
- Light Source Type: LED
- Lamp Type: LED
- Number of Light Sources: 1
- Power Source: Battery Powered
- Switch Type: Motion Sensor
- Special Feature: Motion Sensor
- Material: Plastic
- Base Material: Plastic
- Shade Material: Plastic
- Shade Color: White
- Color: Blue (LED light color)
- Mounting Type: Wall Mount
- Indoor/Outdoor Usage: Indoor
- Is Cordless?: Yes
- Recommended Uses: Security
9. Warranty and Support
For warranty information and customer support, please refer to the documentation provided at the time of purchase or visit the official Bunker Hill Security website. Keep your purchase receipt as proof of purchase for any warranty claims.
If you encounter any issues not covered in this manual, please contact the retailer or manufacturer's customer service for assistance.
