DRUMMOND 1 HP Stainless Steel Shallow Well Pump and Tank User Manual

Product Overview

This DRUMMOND 1 HP Stainless Steel Shallow Well Pump and Tank system is designed for residential water setups. It features a 5-gallon hardened steel alloy tank and a stainless steel housing and volute, ensuring durability and compatibility with potable water due to its lead-free fittings and rubber seals. The pump offers a maximum flow of 950 GPH and a total head lift of 115.5 ft., with a maximum well depth of 26 ft. It operates at 120 Volts (AC) and includes thermal protection with automatic reset for enhanced safety and longevity. The maximum water pressure is 50 PSI.

Image: The DRUMMOND 1 HP Stainless Steel Shallow Well Pump and Tank, featuring a green tank base, a stainless steel pump head, and a green motor housing. A pressure gauge and electrical control box are visible on the pump head.

Important Safety Information

Read and understand all safety warnings and instructions before operating this product. Failure to follow these instructions may result in electric shock, fire, serious injury, or death.

• Always disconnect power before servicing or performing maintenance on the pump.
• Ensure proper grounding to prevent electrical shock.
• Do not operate the pump with damaged cords or plugs.
• Keep children and unauthorized persons away from the pump during operation.
• Install the pump in a dry, well-ventilated area, protected from freezing temperatures.
• Use only for pumping potable water as specified. Do not use for flammable liquids or corrosive chemicals.
• Ensure all plumbing connections are secure and leak-free before operation.

Setup Instructions

1. Unpacking: Carefully remove all components from the packaging. Inspect for any shipping damage.
2. Location: Choose a location that is dry, level, and protected from freezing. Ensure adequate ventilation around the pump.
3. Mounting: Secure the pump to a stable surface using appropriate fasteners through the mounting holes on the base.
4. Plumbing Connections:
   • Connect the suction line from the well to the pump's inlet. Ensure the suction line is airtight to prevent air leaks.
   • Connect the discharge line from the pump's outlet to your household plumbing system.
   • Use thread sealant on all threaded connections to prevent leaks.
5. Priming the Pump:
   • Remove the priming plug on the pump housing.
   • Fill the pump housing completely with water until it overflows.
   • Replace the priming plug securely.
6. Electrical Connection: Connect the pump to a dedicated 120V AC grounded electrical outlet. Ensure the circuit is protected by a ground fault circuit interrupter (GFCI). Consult a qualified electrician if unsure.

Operating Instructions

1. Initial Start-up: After completing the setup and priming, turn on the power to the pump. The pump should start and begin to build pressure.
2. Pressure Monitoring: Observe the pressure gauge. The pump is designed to operate within a pressure range, typically turning on at a lower pressure (e.g., 30 PSI) and off at a higher pressure (e.g., 50 PSI).
3. Air in System: If the pump runs continuously or cycles frequently, there may be air in the system. Re-prime the pump and check all connections for air leaks.
4. Normal Operation: The pump will automatically turn on when water is drawn from the system and the pressure drops, and turn off when the pressure reaches its set maximum.
5. Shutting Down: To temporarily shut down the pump, turn off the electrical power. For extended periods of non-use, drain the pump and plumbing lines to prevent freezing.

Maintenance

Regular maintenance ensures the longevity and efficient operation of your pump.

• Annual Inspection: Annually inspect all plumbing connections for leaks and tighten as necessary. Check electrical connections for corrosion or damage.
• Pressure Tank Check: Periodically check the air pre-charge in the pressure tank. This should be done when the tank is empty of water and the pump is off. Refer to the pressure tank's specific instructions for the correct pressure.
• Winterization: In areas subject to freezing temperatures, the pump and all exposed plumbing lines must be drained completely to prevent damage from ice expansion.
• Cleaning: Keep the pump and motor free of dirt and debris to ensure proper cooling.

Troubleshooting

Technical Specifications

Warranty and Support

This DRUMMOND product is backed by a manufacturer's warranty. Please refer to the warranty card included with your purchase for specific terms and conditions, including coverage duration and limitations. Keep your proof of purchase for warranty claims.

For technical assistance, troubleshooting beyond this manual, or warranty service, please contact DRUMMOND customer support. Contact information can typically be found on the product packaging or the manufacturer's official website.

Note: Protection plans may be available for extended coverage. Check with your retailer for details.