Bosch 00667487 Front Load Washer Door Boot Gasket Instruction Manual

1. Product Overview

The Bosch 00667487 Door Boot Gasket is a genuine replacement part designed for various Bosch and Siemens front load washing machines. This component forms a seal between the washing machine tub and the door, preventing water leaks during operation. It is essential for the proper functioning and water containment of your appliance.

Image 1.1: The Bosch 00667487 Front Load Washer Door Boot Gasket. This circular rubber seal is designed to fit around the opening of a washing machine drum, ensuring a watertight closure when the door is shut.

2. Product Identification and Compatibility

This part, Bosch 00667487, is a direct replacement for the following part numbers:

• 1487488 (original part number, now substituted by 00667487)
• 667487
• AH3481764
• EA3481764
• PS3481764
• PS8732872

This front load washer door boot seal is compatible with many Bosch and Siemens washing machine models. Specifically, it is used on models beginning with WFMC/WFXD and with serial numbers beginning with FD8710-Later. For models with serial numbers beginning with FD8505-FD8709, please order part number 00667489 instead.

Always verify compatibility with your specific appliance model number before purchasing and installing any replacement part.

3. Installation (Setup)

WARNING: Before attempting any repair or installation, ensure the washing machine is completely disconnected from its power source and water supply. Failure to do so can result in electric shock, injury, or property damage. If you are unsure about any step, consult a qualified appliance technician.

1. Preparation: Disconnect power and water. Remove the washer's top panel and front panel, or any other components necessary to access the door boot gasket.
2. Remove Old Gasket: Locate the spring clamps or retaining wires that hold the old gasket in place, both around the door opening and around the outer tub. Carefully remove these clamps/wires and detach the old gasket. Note its orientation for reference.
3. Clean Area: Thoroughly clean the area where the new gasket will be installed, removing any residue, mold, or debris.
4. Install New Gasket: Position the new Bosch 00667487 gasket, ensuring it is correctly oriented (some gaskets have drain holes or alignment marks at the bottom). Carefully stretch and fit the inner lip of the gasket over the outer tub, then secure it with the inner retaining clamp/wire.
5. Secure Outer Lip: Stretch and fit the outer lip of the gasket around the front panel opening, then secure it with the outer retaining clamp/wire. Ensure the gasket is seated evenly and securely without twists or pinches.
6. Reassemble: Reattach all panels and components removed during disassembly.
7. Test: Reconnect water and power. Run a short cycle without laundry to check for leaks around the door seal.

For detailed, model-specific instructions, refer to your washing machine's service manual or a reputable appliance repair guide.

4. Maintenance

Proper maintenance can extend the life of your door boot gasket and prevent issues:

• Wipe Down: After each wash cycle, wipe down the inside of the door boot gasket with a clean cloth to remove moisture, lint, and detergent residue. This helps prevent mold and mildew growth.
• Inspect Regularly: Periodically inspect the gasket for signs of wear, cracks, tears, or foreign objects lodged within its folds.
• Clean Thoroughly: If mold or mildew appears, clean the gasket with a solution of equal parts white vinegar and water, or a washing machine cleaner designed for this purpose. Ensure to rinse thoroughly.
• Leave Door Ajar: When the washer is not in use, leave the door slightly ajar to allow air circulation and prevent moisture buildup inside the drum and gasket area.

5. Troubleshooting

If you experience issues after replacing the door boot gasket, consider the following:

• Water Leaks:
  • Ensure the gasket is seated correctly and evenly around both the tub and the front panel opening.
  • Verify that both retaining clamps/wires are securely in place and properly tensioned.
  • Check for any tears or damage to the new gasket that may have occurred during installation.
  • Confirm that the drain holes (if present) at the bottom of the gasket are clear and not obstructed.
• Mold/Mildew Recurrence:
  • Ensure consistent wiping after cycles and leaving the door ajar for ventilation.
  • Consider running a washer cleaning cycle with a specialized cleaner or bleach.

If issues persist, it is recommended to contact Bosch customer support or a certified technician.

6. Specifications

7. Warranty and Support

This Bosch factory OEM part is covered by Bosch's standard warranty for replacement parts. For specific warranty details, please refer to the documentation included with your purchase or visit the official Bosch website.

For technical assistance, installation inquiries, or to locate authorized service providers, please contact Bosch customer support through their official website or customer service hotline. When contacting support, have your appliance model number and the part number (00667487) readily available.

You can find more information and support resources on the BOSCH Store on Amazon.