Introduction
This manual provides detailed instructions for the proper setup, operation, maintenance, and troubleshooting of your YETI Tundra 65 Cooler. Please read this manual thoroughly before using your cooler to ensure optimal performance and longevity.
Figure 1: Front view of the YETI Tundra 65 Cooler in Aquifer Blue. This image shows the cooler's robust construction and the prominent YETI logo.
Setup
1. Initial Inspection
Upon receiving your YETI Tundra 65, inspect it for any signs of damage during shipping. Ensure all components, including the T-Rex Lid Latches and the dry goods basket, are present and functional.
2. Placement Considerations
For optimal performance, place the cooler on a flat, stable surface. Avoid direct sunlight for extended periods, especially when pre-chilling or storing contents, to maximize ice retention.
3. Pre-Chilling
For best results, pre-chill your Tundra 65 Cooler before loading it with contents. Fill the cooler with sacrificial ice or ice packs 12-24 hours prior to use. This lowers the internal temperature of the cooler walls, significantly improving ice retention.
Figure 2: The YETI Tundra 65 Cooler with its lid open, showcasing the spacious interior and the robust lid construction.
Operation
1. Packing for Optimal Ice Retention
The Tundra 65 features up to 3 inches of PermaFrost Insulation and an extra-thick FatWall Design. To maximize ice retention:
- Use a good ice-to-contents ratio, ideally 2:1 by volume.
- Fill the cooler completely. Air pockets reduce ice retention.
- Use block ice for longer retention, or a mix of block and cubed ice.
- Minimize opening the lid. Each time the lid is opened, cold air escapes.
Figure 3: An illustrative diagram highlighting key features such as the FatWall Design for insulation, PermaFrost Insulation for ice retention, and Rotomolded Construction for durability.
2. Securing the Lid
The T-Rex Lid Latches are constructed of heavy-duty rubber, designed for durability and a secure seal. Pull the latches firmly over the molded keepers to ensure the lid is tightly closed. The ColdLock Gasket creates a freezer-quality seal to block out heat.
3. Draining the Cooler
The Vortex Drain System is leakproof and designed for quick and easy draining. Simply unscrew the drain plug located at the bottom of the cooler to release melted ice water.
4. Carrying and Transporting
The Tundra 65 is equipped with LipGrip Handles for easy carrying and DoubleHaul Handles made of military-grade polyester rope for extra durability when transporting with two people. For securing the cooler during transport, utilize the AnchorPoint Tie-Down Slots molded into the cooler body, suitable for boats, trailers, or truck beds.
Figure 4: A comprehensive diagram detailing the additional features of the YETI Tundra 65, including T-Rex Lid Latches, AnchorPoint Tie-Down Slots, NeverFail Hinge System, InterLock Lid System, ColdLock Gasket, LipGrip Handles, DoubleHaul Handles, Vortex Drain System, and BearFoot Non-Slip Feet.
Maintenance
1. Cleaning Instructions
Clean your YETI Tundra 65 after each use. Use mild soap and warm water with a soft cloth or sponge. For stubborn stains or odors, a solution of bleach and water (1:6 ratio) can be used. Rinse thoroughly with fresh water and allow to air dry with the lid open to prevent mildew.
2. Storage Recommendations
Store the cooler in a cool, dry place away from direct sunlight. Keep the lid slightly ajar during storage to allow for air circulation and prevent odors from building up inside.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Ice melts too quickly | Cooler not pre-chilled; insufficient ice; frequent lid opening; warm contents. | Pre-chill cooler; use more ice (2:1 ratio); minimize lid openings; pre-chill contents. |
| Lid not sealing properly | Latches not fully engaged; debris on ColdLock Gasket. | Ensure T-Rex Latches are securely fastened; clean ColdLock Gasket and rim of cooler. |
| Unpleasant odor inside cooler | Improper cleaning or storage. | Clean thoroughly with bleach solution; store with lid slightly ajar. |
Specifications
The YETI Tundra 65 Cooler is engineered for durability and superior ice retention. Key specifications are as follows:
- Model Name: Tundra 65
- Capacity: 57.6 Liters
- External Dimensions (L x W x H): 30 1/2 in x 17 1/2 in x 16 in (approx. 77.5 cm x 44.5 cm x 40.6 cm)
- Internal Dimensions (L x W x H): 23 1/8 in x 11 1/8 in x 10 5/8 in (approx. 58.7 cm x 28.2 cm x 27 cm)
- Empty Weight: 29 lbs (approx. 13.15 kg)
- Material: Rotomolded Polyethylene, Rubber, Polyester, Polyurethane (PU)
- Included Components: Dry goods basket
- Special Features: Portable, Bear-Resistant Certified
Figure 5: A detailed diagram showing the external and internal dimensions of the YETI Tundra 65 Cooler, along with its capacity in cans of beer and pounds of ice.
Warranty & Support
YETI products are built to last. For information regarding the warranty coverage for your Tundra 65 Cooler, please refer to the official YETI website or contact YETI customer support directly. Keep your proof of purchase for warranty claims.
For further assistance, product registration, or to view frequently asked questions, visit the official YETI support page or contact their customer service team.
