1. Introduction
This manual provides comprehensive instructions for the assembly, operation, and maintenance of your Mount-It! Standing Desk Converter MI-7914. This adjustable workstation is designed to enhance your ergonomic setup by allowing seamless transitions between sitting and standing positions, promoting a healthier work environment. It features a dual monitor mount for increased productivity.
2. Safety Information
- Read all instructions carefully before assembly and use. Failure to do so may result in injury or product damage.
- Do not exceed the maximum weight capacity of 33 pounds for the desk converter and 22 pounds per monitor.
- Ensure all screws and connections are securely tightened before use. Periodically check for loose connections.
- Keep children and pets away from the product during assembly and operation.
- Use the product on a stable, level surface.
- Exercise caution when adjusting the height to avoid pinching fingers or other body parts.
3. Package Contents
Verify that all components are present before beginning assembly. If any parts are missing or damaged, contact Mount-It! customer support.
- Standing Desk Converter Base
- Upper Work Surface
- Keyboard Tray
- Dual Monitor Mount Assembly
- Hardware Kit (screws, washers, Allen wrenches)
- Wrist Pad
4. Setup and Assembly
Follow these steps to assemble your standing desk converter. It is recommended to have a second person assist with lifting and positioning the unit.
4.1 Unpacking and Preparation
Carefully remove all components from the packaging. Lay them out on a clean, flat surface to identify each part.
4.2 Attaching the Keyboard Tray
Align the keyboard tray with the designated attachment points on the main desk converter frame. Secure it using the provided screws and tools.
4.3 Installing the Dual Monitor Mount
The monitor mount can be installed in various configurations. Choose the appropriate method for your setup (e.g., grommet mount or clamp mount if applicable, though this model typically integrates directly into the desk). Attach the main pole to the designated hole on the upper work surface. Then, attach the monitor arms to the pole.
Image: Standing Desk Converter with Dual Monitor Mount (without monitors attached)
4.4 Mounting Your Monitors
Attach your monitors to the VESA plates on the monitor arms. This unit supports VESA patterns of 75x75mm and 100x100mm. Ensure the monitors are securely fastened. The monitor arms allow for 180° swivel, 360° rotation, and +/-90° tilt for optimal viewing angles.
Image: Full Motion Mount Capabilities
4.5 Placing on Your Desk
With assistance, carefully lift the assembled desk converter and place it on your existing desk. Ensure it is centered and stable.
5. Operating Instructions
5.1 Height Adjustment
The Mount-It! Standing Desk Converter features a gas spring lift mechanism for smooth height adjustments. To raise or lower the workstation, locate the adjustment lever (typically on the side of the upper work surface). Squeeze the lever and gently guide the desk to your desired height. Release the lever to lock it in place. The height range is from 5.7 inches (minimum) to 17.1 inches (maximum).
Image: Height Adjustment Mechanism and Range
5.2 Monitor Adjustment
Once monitors are mounted, you can adjust their position for optimal viewing comfort. The monitor arms allow for:
- Swivel: Rotate monitors horizontally up to 180 degrees.
- Tilt: Adjust the vertical angle of your monitors up to +/-90 degrees.
- Rotation: Rotate monitors 360 degrees to switch between landscape and portrait orientation.
- Height: Adjust the height of the monitors along the central pole.
Use the provided Allen wrenches to loosen or tighten joints as needed for adjustment, then secure them to maintain position.
Image: Sit or Stand Functionality
5.3 Cable Management
Utilize the integrated cable management clips or ties to keep your workspace tidy and prevent cables from interfering with the desk's movement.
6. Maintenance
- Cleaning: Wipe surfaces with a soft, damp cloth. Avoid abrasive cleaners or solvents.
- Inspection: Periodically check all bolts, screws, and connections to ensure they are tight. Retighten as necessary.
- Gas Spring: The gas spring mechanism is designed for long-term use and generally requires no maintenance. If you experience issues with height adjustment, ensure no obstructions are present.
7. Troubleshooting
- Desk does not stay at desired height: Ensure the adjustment lever is fully released. Check if the weight on the desk exceeds the maximum capacity.
- Monitors sag or tilt: Tighten the VESA plate screws and the tension adjustments on the monitor arms using the provided Allen wrenches.
- Difficulty raising/lowering: Ensure no cables or objects are obstructing the mechanism. Check if the weight on the desk is evenly distributed and within limits.
- Wobbling: Ensure the desk converter is placed on a stable, flat surface. Check all assembly screws for tightness.
8. Specifications
| Model Number | MI-7914 |
| Brand | Mount-It! |
| Material | Other (typically steel and engineered wood) |
| Color | Black |
| Load Capacity (Desk) | 33 Pounds |
| Load Capacity (Per Monitor) | 22 Pounds |
| Height Adjustment Range | 5.7 inches to 17.1 inches |
| Top Platform Dimensions | 23.6" x 15.7" |
| Keyboard Tray Dimensions | 26.7" x 11.8" |
| VESA Compatibility | 75x75mm, 100x100mm |
| Item Weight | 47 pounds |
| Product Dimensions (L x W x H) | 11.42 x 3.74 x 8.27 inches (packaged) |
Image: Product Dimensions
9. Warranty and Support
Mount-It! products are designed for durability and performance. For specific warranty information or technical support, please refer to the official Mount-It! website or contact their customer service department directly. Keep your purchase receipt for warranty claims.
