1. Introduction
Bona Floor Polish is a ready-to-use, high-gloss maintenance product designed to restore shine and provide durable protection for a variety of hard floor surfaces. This polish helps to fill in micro-scratches, extending the lifespan and enhancing the appearance of your flooring.
It is suitable for most hard floors, including:
- Laminate
- PVC
- Linoleum
- Unglazed tiles (ceramic, broken stone)
- Sealed stone
- Marble
A single 1-liter bottle provides coverage for approximately 50 square meters (538 square feet) of floor area.
Image: Bona Floor Polish bottle illustrating coverage of 50 square meters.
Image: Examples of compatible hard floor surfaces.
2. Safety Information & Precautions
Please read and follow all safety instructions carefully before using this product.
- Keep out of reach of children.
- Always test the product on a small, inconspicuous area of the floor to check for adhesion and desired result before full application.
- Do not apply to unpolished, waxed, or oiled floors.
- Ensure the room temperature is between 18-25°C (64-77°F) during application and drying for optimal results.
- The product contains methylisothiazolinone.
This product is GREENGUARD GOLD certified, ensuring low chemical emissions and a safer environment for your family and pets.
Image: GREENGUARD GOLD certification logo, indicating low chemical emissions.
Image: Illustrating floor protection and safety for household members and pets.
3. Preparation (Setup)
- Clean the Floor: Ensure the floor is thoroughly cleaned with a suitable floor cleaner (e.g., Bona Floor Cleaner) to remove all dirt, grime, and previous cleaning product residues. The floor must be completely dry before applying the polish.
- Remove Furniture: Clear the area of all furniture and rugs to allow for unobstructed application and drying.
- Test Area: As mentioned in the safety section, always test the polish on a small, hidden area of the floor to ensure compatibility and desired finish.
4. Application (Operating Instructions)
Follow these steps for optimal application of Bona Floor Polish:
- Shake Well: Shake the bottle thoroughly before use. Do not dilute the product.
- Apply Polish: Pour a wavy line of polish directly onto a small section of the clean, dry floor.
- Spread Evenly: Using a Bona Microfiber Applicator Pad (or similar clean, damp microfiber pad), spread the polish evenly across the section, working with the grain of the floor if applicable. Ensure a thin, uniform coat without puddles.
- Continue Application: Move to the next section, overlapping slightly with the previously polished area, and continue until the entire floor is covered.
- Drying Time (Light Traffic): Allow the floor to dry for at least 1 hour before allowing light foot traffic.
- Drying Time (Full Curing): For full curing and before replacing furniture or rugs, allow the floor to dry for 12 hours.
Image: Back of the product bottle illustrating the application process (Clean, Shake, Apply, Spread, Dry 1hr, Furnish 12hrs).
Image: A person applying Bona Floor Polish to a hard floor using a mop applicator.
Image: Close-up of the polish being applied to a tiled floor.
5. Post-Application Care (Maintenance)
- Regular Cleaning: For daily or weekly cleaning, use a pH-neutral cleaner specifically designed for hard floors, such as Bona Floor Cleaner, to maintain the polish's integrity.
- Reapplication: Reapply Bona Floor Polish as needed, typically every 1-4 months, depending on foot traffic and wear. Always follow the preparation and application steps outlined above.
- Avoid Harsh Cleaners: Do not use abrasive cleaners, ammonia-based products, or wax-based cleaners, as these can damage the polish layer.
Image: A child enjoying a freshly polished, shiny floor.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Uneven shine or dull spots | Incomplete cleaning before application; uneven application of polish; insufficient drying time. | Ensure floor is thoroughly clean and dry. Apply polish in thin, even coats. Allow adequate drying time between coats if applying multiple. |
| Streaks or hazy appearance | Too much polish applied; applicator pad was dirty or too wet; high humidity during drying. | Apply thinner coats. Use a clean, slightly damp (not wet) applicator pad. Ensure good ventilation and appropriate room temperature. |
| Polish not adhering | Floor was not clean; previous wax or oil residue; applied to an incompatible floor type. | Ensure floor is free of all contaminants. Verify floor type is compatible with Bona Floor Polish. Always perform a test patch. |
7. Specifications
| Attribute | Detail |
|---|---|
| Product Name | Bona Floor Polish |
| Model Number | WP511013025 |
| Volume | 1000 Milliliters (1 Liter) |
| Form | Liquid |
| Brand | Bona |
| Dimensions (L x W x H) | 6.5 x 11.5 x 25 cm (2.56 x 4.53 x 9.84 inches) |
| Weight | 1.1 kilograms (2.43 lbs) |
| Country of Origin | Sweden |
| Specific Uses | Ceramic, Linoleum, Stone, Laminate, PVC |
| Special Feature | Low odor |
| Material Feature | Acid-free |
| Scent | Unscented |
| Certification | GREENGUARD GOLD |
Image: Product bottle illustrating its dimensions.
8. Warranty & Support
For detailed warranty information, please refer to the manufacturer's official website or the documentation included with your purchase. Bona products are known for their quality and are recommended by professionals since 1919.
Contact Information:
Bona Germany:
Bona Vertriebsgesellschaft mbH
Industriestraße 12, D-65549 Limburg
Phone: +49 6431 / 4006-0
Website: www.bona.com
Bona Austria:
Bona Austria GmbH
Mayrwiesstraße 21, A-5300 Hallwang bei Salzburg
Phone: +43 662 / 66 19 22
Hotline: 0800 22 82 82
Website: www.bona.com
