1. Introduction
This manual provides essential information for the proper installation, operation, and maintenance of your SaferCCTV Satellite 20dB Gain Inline Amplifier, Model CCTV-20A. This device is designed to boost satellite signals within the 950-2150MHz frequency range, helping to minimize signal loss over long cable runs or due to in-line devices. It is compatible with all satellite systems and is a DC passive unit, requiring no external power supply.
2. Safety Information
- Ensure all connections are secure and properly insulated to prevent electrical hazards.
- Do not expose the amplifier to moisture or extreme temperatures.
- Handle the device with care to avoid physical damage.
- This device is intended for satellite signal amplification only. Do not use it for other purposes.
3. Package Contents
- 1 x SaferCCTV Satellite 20dB Gain Inline Amplifier (Model: CCTV-20A)
4. Product Overview
The SaferCCTV Satellite 20dB Gain Inline Amplifier is a compact and efficient solution for improving satellite signal strength. It features a robust design suitable for various satellite applications.
Key Features:
- Provides up to 20dB gain to minimize signal loss.
- DC passive operation, eliminating the need for a separate power supply.
- Compatible with all satellite systems on the market.
- Designed for use with RG6 cables, especially for runs over 50 feet.
Figure 4.1: Front view of the SaferCCTV Satellite 20dB Gain Inline Amplifier.
Figure 4.2: Top view showing 'ANT' (Antenna) and 'POWER IN' labels on the amplifier.
Figure 4.3: Dimensions of the amplifier, approximately 80mm in length, 30mm in width, and 19mm in height.
5. Setup
Proper placement of the inline amplifier is crucial for optimal performance. Follow these steps for installation:
- Identify Signal Loss Point: The amplifier should be installed where the satellite signal begins to degrade. This is typically after a long cable run or before a distribution point.
- Optimal Placement: For best results, install the amplifier within 38 inches (approximately 96.5 cm) of the point where the signal starts to weaken.
- Cable Type: This amplifier is designed for use with RG6 coaxial cables. Ensure your existing cabling is compatible.
- Connection: Connect the satellite signal source (e.g., satellite dish output) to the port labeled 'POWER IN' on the amplifier. Connect the output of the amplifier (labeled 'ANT') to your satellite receiver or distribution system. Ensure all F-connectors are tightened securely.
- Power: As a DC passive device, the amplifier draws power directly from the satellite receiver or LNB (Low-Noise Block downconverter) via the coaxial cable. No external power adapter is needed.
6. Operating Instructions
Once properly installed, the SaferCCTV Satellite 20dB Gain Inline Amplifier operates automatically. It functions by boosting the incoming satellite signal by approximately 20dB across the 950-2150MHz frequency range. This amplification helps to compensate for signal attenuation caused by long cable lengths or other passive components in your satellite system.
Since it is a DC passive amplifier, it does not require any manual controls or adjustments. It will draw the necessary power through the coaxial cable from your satellite receiver or LNB.
7. Maintenance
The SaferCCTV Satellite 20dB Gain Inline Amplifier requires minimal maintenance. Follow these guidelines to ensure its longevity and performance:
- Cleaning: Periodically wipe the exterior of the amplifier with a soft, dry cloth to remove dust and dirt. Do not use liquid cleaners or solvents.
- Connections: Regularly check all coaxial cable connections to ensure they remain tight and free from corrosion. Loose connections can lead to signal degradation.
- Environmental Protection: If installed outdoors, ensure the amplifier is protected from direct weather exposure using appropriate weatherproofing techniques for coaxial connections.
- Storage: If storing the amplifier, keep it in a cool, dry place away from direct sunlight and extreme temperatures.
8. Troubleshooting
If you experience issues with your satellite signal after installing the amplifier, consider the following troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| No signal or worse signal after installation |
|
|
| Weak or intermittent signal |
|
|
9. Specifications
| Feature | Specification |
|---|---|
| Model Number | CCTV-20A |
| Gain | 20dB |
| Frequency Range | 950-2150MHz |
| Power Supply | DC Passive (No separate power supply required) |
| Compatibility | All satellite applications, Dish Network, Directv, FTA |
| Recommended Cable | RG6 (for runs over 50 FT) |
| Optimal Installation Distance | Within 38 inches of signal decreasing point |
| Package Dimensions | 3.9 x 3.7 x 0.59 inches |
| Item Weight | 2.08 ounces |
| Impedance | 50 Ohms |
| Color | Silver, White |
10. Warranty Information
SaferCCTV products are manufactured to high-quality standards. For specific warranty details, please refer to the product packaging or contact SaferCCTV customer service. Keep your purchase receipt as proof of purchase for any warranty claims.
11. Support
If you have any questions, require technical assistance, or encounter issues not covered in this manual, please contact SaferCCTV customer service. Refer to the contact information provided with your product or visit the official SaferCCTV website for support resources.