Peg Perego Viaggio Shuttle Booster Car Seat

Important Safety Information

Read all instructions and warnings before using this booster seat. Failure to follow these instructions could result in serious injury or death. Keep this manual for future reference.

Child Requirements

• Minimum Weight: 40 lbs
• Maximum Weight: 120 lbs
• Minimum Height: 39 inches
• Maximum Height: 63 inches
• Orientation: Forward Facing

Vehicle Requirements

• This booster seat is designed for use with a vehicle's lap and shoulder belt system.
• Ensure your vehicle is equipped with LATCH anchors for secure installation, if using the integrated rigid LATCH system.

WARNING: Always secure the child with the vehicle's lap and shoulder belt. The LATCH system secures the booster seat to the vehicle, but does not secure the child.

Product Overview

The Peg Perego Viaggio Shuttle is a booster car seat designed for older children, providing a secure and comfortable ride. It features an integrated rigid LATCH system for easy installation and stability, and a comfortable urethane foam cushion.

Key Features

• Integrated Rigid LATCH System: Connects to vehicle LATCH anchors for secure placement. Can be retracted for use in vehicles without LATCH.
• Blind Lock System: Protects the seat from inadvertent release when using the rigid LATCH.
• Comfortable Cushion: Features a super layer of soft urethane foam.
• Cup Holder: Included for convenience, can be attached to either side.
• Carry Handle: For easy transport.

Image: The Peg Perego Viaggio Shuttle booster car seat in Crystal Black, showing its compact design and padded seating area.

Setup and Installation

Follow these steps to properly install your Peg Perego Viaggio Shuttle booster car seat.

Step-by-Step Installation

1. Prepare the Booster Seat: Place the booster seat on the vehicle's seat.
2. Extend LATCH Connectors: Locate the yellow handle on the side of the booster seat. Pull the handle to extend the integrated rigid LATCH connectors.

   Image: The booster seat with its yellow LATCH connectors extended from the base, ready for attachment to vehicle anchors.

3. Attach to Vehicle LATCH Anchors: Align the LATCH connectors with your vehicle's lower LATCH anchors. Push the booster seat firmly against the vehicle seatback until both connectors click into place. Ensure a secure connection.
4. Secure the Booster Seat: Push the booster seat firmly towards the vehicle seatback to remove any slack and ensure a tight fit. The Blind Lock System will engage to prevent accidental release.
5. Retract LATCH Connectors (if not using LATCH): If your vehicle does not have LATCH anchors, the rigid LATCH connectors can be pushed back into the booster seat.

   Image: The booster seat with its LATCH connectors retracted into the base, suitable for vehicles without LATCH anchors.

6. Install Cup Holder: The included cup holder can be slid into the designated slot on either side of the booster seat.

   Image: The booster seat with the detachable cup holder installed on the side.

   

   Image: A close-up view of the detachable cup holder for the booster seat.

Video Installation Guide

For a visual guide on installation, please watch the official video below:

Operating Instructions

Once installed, ensure your child is properly secured in the booster seat using the vehicle's lap and shoulder belt.

Securing Your Child

1. Position your child in the booster seat.
2. Route the vehicle's lap belt low across your child's hips, touching the thighs.
3. Route the shoulder belt across your child's chest and collarbone, ensuring it does not rest on the neck or face.
4. Buckle the vehicle's seat belt.
5. Check for a snug fit. The booster seat helps position the vehicle's seat belt correctly on your child's body.

IMPORTANT: Always ensure the vehicle's seat belt is properly positioned and snug. Never use only the lap belt with this booster seat.

Maintenance and Care

Cleaning Instructions

• Fabric Cover: The fabric cover can be removed for cleaning. Refer to the care label on the fabric for specific washing instructions. Typically, machine wash cold on a delicate cycle with mild detergent. Air dry.
• Plastic Components: Wipe plastic parts with a damp cloth and mild soap. Do not use abrasive cleaners or solvents.
• LATCH Connectors: Keep LATCH connectors clean and free of debris.

Storage

• Store the booster seat in a cool, dry place away from direct sunlight when not in use.
• Ensure the LATCH connectors are retracted if storing in a vehicle without LATCH anchors.

Troubleshooting

Common Issues and Solutions

• Booster Seat Feels Loose:
  • Ensure the LATCH connectors are fully engaged with the vehicle's anchors. Push the booster seat firmly into the vehicle seat to remove slack.
  • If not using LATCH, ensure the vehicle's seat belt is routed correctly and tightened securely around the child and booster.
• Cup Holder Not Secure:
  • Verify the cup holder is fully slid into its designated slot until it clicks or feels firm.
  • Avoid placing excessively heavy or unstable items in the cup holder.
• Vehicle Seat Belt Does Not Fit Child Correctly:
  • Ensure the child meets the minimum height and weight requirements for the booster seat.
  • Adjust the vehicle's headrest or seat position if possible to optimize belt fit. The shoulder belt should lie flat across the collarbone, not on the neck.

Specifications

Image: Diagram showing the dimensions of the Peg Perego Viaggio Shuttle booster car seat: 17.25 inches length, 16 inches width, and 9.5 inches height.

Warranty and Support

For warranty information and customer support, please refer to the official Peg Perego website or contact their customer service department. Keep your proof of purchase for warranty claims.

Visit Peg Perego Customer Service