KING GATES Novo Click Outdoor Key Switch User Manual

Introduction

Thank you for choosing the KING GATES Novo Click Outdoor Key Switch. This pre-wired microswitch key switch is designed for reliable outdoor operation, providing secure access control for various applications, particularly gate automation systems. Please read this manual carefully before installation and operation to ensure proper use and longevity of the product.

This manual provides essential information regarding the product's features, installation procedures, operational guidelines, and maintenance tips.

Important Safety Information

Always observe the following safety precautions to prevent injury or damage to the product:

• Installation should only be performed by qualified personnel in accordance with local electrical codes and regulations.
• Disconnect power to the gate automation system before performing any installation, maintenance, or troubleshooting.
• Ensure all wiring connections are secure and properly insulated to prevent short circuits.
• Do not modify the key switch or its components. Unauthorized modifications may void the warranty and pose safety risks.
• Keep keys out of reach of children and unauthorized individuals.
• This device is designed for outdoor use; however, ensure it is mounted in a location that minimizes direct exposure to extreme weather conditions if possible.

Product Overview

Figure 1: KING GATES Novo Click Outdoor Key Switch. This image shows the compact, grey-colored key switch unit with a central black circular keyhole and the "KING GATES" logo vertically aligned on the right side of the casing.

The KING GATES Novo Click Outdoor Key Switch is a robust and reliable solution for controlling access to automated gates or other systems. It features a durable plastic casing designed for outdoor environments and comes pre-wired for ease of installation.

Package Contents

Please verify that all items are present in the package:

• 1 x KING GATES Novo Click Outdoor Key Switch
• 2 x Keys for operation
• Mounting hardware (screws, wall plugs - may vary)

Specifications

Setup and Installation

Tools Required: Drill, screwdriver, wire strippers, voltage tester.

1. Mounting the Key Switch

1. Choose a suitable outdoor location for mounting the key switch. Ensure it is easily accessible but protected from direct impact or excessive moisture.
2. Mark the drilling points on the wall or post using the key switch as a template.
3. Drill pilot holes at the marked points. Insert wall plugs if mounting on masonry.
4. Secure the key switch to the mounting surface using the provided screws. Do not overtighten.

2. Wiring Connections

The Novo Click key switch comes pre-wired with a microswitch. Refer to your gate automation system's control unit manual for specific wiring diagrams. Generally, the key switch will connect to the control unit's input terminals for manual operation (e.g., opening/closing the gate).

• Identify Wires: The key switch typically has two wires connected to the microswitch (common and normally open/closed).
• Connect to Control Unit: Connect these wires to the appropriate terminals on your gate control board. This usually involves connecting to a common terminal and a command input terminal (e.g., "OPEN" or "STEP-BY-STEP").
• Secure Connections: Ensure all connections are tight and insulated. Use appropriate cable glands if routing wires through conduit to maintain weather resistance.

Note: Always consult the wiring diagram of your specific gate automation system for correct connections. Incorrect wiring can damage the control unit or the key switch.

Operating Instructions

The KING GATES Novo Click Key Switch operates as a simple ON-OFF switch, activating a command on your gate automation system when the key is turned.

1. Insert one of the provided keys into the keyhole of the switch.
2. Turn the key to activate the desired function (e.g., open gate, close gate, or step-by-step operation, depending on how it's wired to your control unit). The key will typically turn a quarter or half turn.
3. Release the key. The switch will return to its neutral position, and the command will be executed by the gate control unit.
4. Remove the key after use to secure the system.

Tip: If the gate does not respond, ensure the key is fully inserted and turned, and check the power supply to the gate automation system.

Maintenance

The KING GATES Novo Click Key Switch requires minimal maintenance. Regular checks can help ensure its long-term reliability:

• Cleaning: Periodically wipe the exterior of the key switch with a soft, damp cloth to remove dirt and debris. Do not use abrasive cleaners or solvents.
• Keyhole: If the keyhole becomes stiff, a small amount of graphite powder or a silicone-based lubricant can be applied. Avoid oil-based lubricants as they can attract dust.
• Connections: Annually, inspect the wiring connections for any signs of corrosion or loosening. Ensure they remain secure and protected from moisture.
• Physical Damage: Check for any cracks or damage to the casing, especially after severe weather. Damaged units should be replaced to maintain weather resistance.

Troubleshooting

If the problem persists after attempting these solutions, please contact KING GATES customer support or a qualified technician.

Warranty and Support

This product is covered by the standard manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official KING GATES website. Keep your proof of purchase for warranty claims.

For technical support, troubleshooting assistance, or spare parts, please contact your authorized KING GATES dealer or customer service. When contacting support, please have your product model (Linea "NOVO") and ASIN (B01MUG48H4) ready.

Return Policy: As per Amazon's policy, this product may be eligible for return within 30 days of receipt. Please refer to Amazon's return policy for full details.