Stelpro UHC2002WCW
Stelpro Uniwatt UHC2002WCW Convector Heater User Manual
Model: UHC2002WCW | Brand: Stelpro
1. Safety Information
Important Safety Instructions:
- Protect the unit with appropriate circuit breakers or fuses according to the nameplate.
- Ensure that the supply voltage (volts) corresponds to that indicated on the nameplate.
- This unit must be grounded. Use copper conductors only.
- Use power leads suitable for 75°C (167°F).
- Switch off the power supply to the unit at the circuit breaker/fuse before installation, repair, and cleaning.
- Ensure that the unit is designed for the intended use (consult the product catalog or a representative if necessary).
- Recommended heating capacity: 1.25 W/cubic foot (0.03 m³).
2. Product Overview
The Stelpro Uniwatt UHC2002WCW is a modern, surface-mounted convector heater designed for quiet operation and efficient heating in various indoor spaces. This model provides 2000 watts of heating capacity at 240V (1500W at 208V) and requires an external wall thermostat for temperature control.
Key Features:
- Heating Capacity: 2000W (240V) / 1500W (208V), suitable for large rooms.
- Control: Requires an external wall thermostat (sold separately).
- Quiet Operation: Engineered for minimal noise.
- Design: Sleek, modern look with rounded corners and a durable steel cabinet.
- Installation: Designed for surface mounting with a concealed bracket.
- Material: 22-gauge steel front and cabinet.
- Special Feature: Cool Touch Exterior.
Product Components:
This image displays the front of the Stelpro Uniwatt UHC2002WCW convector heater, highlighting its clean white finish and the top air outlet grille.
A detailed view of the heater's durable white finish, which is an epoxy-polyester powdercoat designed for a crisp matte look.
This image shows the side profile of the convector heater, emphasizing its slim design which allows it to blend discreetly into any room.
An illustration detailing the physical dimensions of the heater, including its width, height, and depth, crucial for planning installation space.
3. Setup and Installation
This convector heater is designed for surface mounting and hardwired electric connection. Ensure all safety precautions are followed before beginning installation.
3.1 Determining Heating Requirements:
Before installation, determine the appropriate wattage for your space. The recommended heating capacity is 1.25 W per cubic foot (0.03 m³).
This table provides a guide to determine the required power (in watts) based on the area to be heated (in square feet or square meters), helping users select the correct heater for their space.
3.2 Mounting the Heater:
The heater features a concealed mounting bracket for a clean and professional appearance. Refer to the detailed instructions provided in the packaging for specific mounting steps.
This image illustrates the concealed mounting bracket, which allows the heater to be securely attached to the wall while maintaining a sleek, integrated look.
This image highlights the ease of installation for the convector heater, emphasizing its user-friendly design for mounting.
3.3 Electrical Connection:
This unit requires a 240V hardwired electric connection. Ensure the power supply is off at the circuit breaker before making any electrical connections. Connect the black and red wires, and ensure the ground wire is securely attached.
A diagram showing the necessary wiring for a 240V hardwired connection, including the black, red, and ground wires, for safe and proper electrical setup.
Video: Stelpro SOR1 High-End Convector Overview
This video provides an overview of a Stelpro high-end convector, demonstrating its features and design, which may be similar to the UHC2002WCW model.
4. Operation
The UHC2002WCW convector heater operates in conjunction with an external wall thermostat (sold separately). This thermostat will control the heater's on/off cycles to maintain the desired room temperature.
4.1 Wattage Settings:
The heater includes an internal switch to select between 1000W and 2000W output. This allows for flexibility based on the heating needs of the room. To adjust the wattage, the front panel must be removed, and the switch located inside the unit should be toggled. Always ensure the power supply is disconnected before accessing internal components.
This image shows the internal components of the heater, specifically highlighting the switch that allows users to select between 1000W and 2000W heating modes.
4.2 Thermostat Control:
Once installed and wired, the heater will respond to the external wall thermostat. Set the desired temperature on your wall thermostat, and the heater will activate or deactivate to maintain that setting.
5. Maintenance
Regular maintenance ensures optimal performance and longevity of your convector heater. Always disconnect power at the circuit breaker before performing any maintenance.
- Cleaning: Periodically wipe the exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure no liquid enters the heater.
- Dust Removal: Gently vacuum or brush away any dust accumulation from the air intake and outlet grilles.
- Inspection: Annually inspect the power connections and mounting for any signs of wear or damage. If any issues are found, consult a qualified electrician.
6. Troubleshooting
If you experience issues with your heater, refer to the following common troubleshooting steps. For problems not listed here, contact customer support or a qualified electrician.
| Problem | Possible Cause | Solution |
|---|---|---|
| Heater does not turn on. | No power supply; Thermostat set too low; Internal wattage switch off. | Check circuit breaker/fuse. Ensure thermostat is set above room temperature. Verify internal wattage switch is in 1000W or 2000W position (power off before checking). |
| Insufficient heat output. | Wattage setting too low; Room size exceeds heater capacity; Airflow obstruction. | Check internal wattage switch (set to 2000W if needed). Ensure heater capacity matches room size. Clear any obstructions from grilles. |
| Unusual noises during operation. | Loose components; Dust accumulation in fan. | Ensure all mounting screws are tight. Clean fan and internal components (power off first). If noise persists, contact support. |
7. Specifications
| Feature | Detail |
|---|---|
| Brand | Stelpro |
| Model Number | UHC2002WCW |
| Colour | White |
| Product Dimensions | 88.9 x 10 x 44.61 cm (35 x 3.9 x 17.5 inches); 8.57 kg (18.9 lbs) |
| Power/Wattage | 2000 watts (at 240V) |
| Voltage | 240 Volts |
| Material | Steel |
| Special Feature | Cool Touch Exterior |
| Heating Method | Convection |
| Mounting Type | Wall Mount |
| Indoor/Outdoor Usage | Indoor |
| Place of Business | Stelpro - 1041 Rue Parent, Saint-Bruno-de-Montarville, QC J3V 0A2 |
8. Warranty and Support
Stelpro products are proudly made in Canada. For warranty information, technical support, or service inquiries, please refer to the official Stelpro website or contact their customer service department. Keep your purchase receipt for warranty claims.
This image features the "Proudly Made in Canada" logo, indicating the origin of Stelpro products.
Related documentsUHC2002WCW
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.