SilverStone Technology ES02-USB

Introduction

The SilverStone ES02-USB is a convenient wireless remote switch kit designed to provide remote control over your computer's power and reset functions. Utilizing standard 2.4GHz RF wireless technology and connecting via the motherboard's USB 2.0 9-pin internal header, this kit allows you to turn on, turn off, or reset your computer from a distance of up to 20 meters in free space. It includes a Y-cable to ensure that your computer case's existing power and reset buttons remain functional alongside the ES02-USB.

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your ES02-USB kit, along with product specifications.

Package Contents

Please verify that all items listed below are present in your package:

• ES02-USB 9-Pin Adapter (Receiver Board)
• Wireless Remote Control
• Power / Reset Switch Y-Cable
• Left and Right Angled USB Adapters (Optional use)
• CR2032 Battery (Pre-installed in remote)

Image: The SilverStone ES02-USB kit showing the wireless remote, the receiver board, and the product packaging.

Setup and Installation

Follow these steps to properly install your SilverStone ES02-USB kit:

1. Prepare your computer: Turn off your computer and unplug the power cord from the wall outlet. Open your computer case to access the motherboard.
2. Locate the USB 2.0 9-pin header: Identify an available USB 2.0 9-pin header on your motherboard. This is typically labeled as 'USB', 'F_USB', or similar.
3. Connect the ES02-USB Receiver Board: Plug the ES02-USB receiver board onto the identified USB 2.0 9-pin header. Ensure the orientation is correct to avoid damage. If needed, use the included left or right angled USB adapters for better cable management or clearance.
   

   Image: Close-up of the ES02-USB receiver board, showing the 9-pin connector for motherboard attachment.
4. Connect the Power/Reset Y-Cable:
   • Disconnect your computer case's existing Power SW and Reset SW cables from the motherboard's front panel headers.
   • Connect these disconnected Power SW and Reset SW cables from your case to the corresponding male pins on the ES02-USB Y-cable.
   • Connect the female ends of the ES02-USB Y-cable to the Power SW and Reset SW headers on your motherboard. This setup allows both the remote and your case buttons to function.
   

   Image: The Power SW and Reset SW Y-cables, which allow simultaneous use of the remote and case buttons.

5. Secure components: Ensure all connections are firm and cables are routed neatly to avoid interference with other components or fans.
6. Close the case and power on: Close your computer case, plug the power cord back in, and power on your computer. The ES02-USB is now ready for use.

Image: The complete SilverStone ES02-USB kit, including the remote, receiver board, and the connecting cable, illustrating the components involved in the setup.

Operating Instructions

The ES02-USB remote control features two primary buttons for managing your computer:

• Power Button (⏻): Press this button to turn your computer on or off. A short press will typically initiate a power-on sequence or a graceful shutdown (depending on your operating system's power settings). A long press (hold for 4-5 seconds) will force a power off.
• Reset Button (↻): Press this button to restart your computer. This functions identically to the physical reset button on your computer case.

The remote operates using 2.4GHz RF wireless technology, providing an effective operating range of up to 20 meters (approximately 65 feet) in open space. Performance may vary depending on environmental factors such as obstacles, walls, and other wireless interference.

Image: A hand holding the compact SilverStone ES02-USB wireless remote control, demonstrating its ergonomic design.

Maintenance

The SilverStone ES02-USB requires minimal maintenance. The primary maintenance task is battery replacement for the wireless remote control.

Battery Replacement

The remote control uses one CR2032 coin cell battery. When the remote's range decreases significantly or it stops responding, it's likely time to replace the battery.

1. Locate the battery compartment on the back of the remote control.
2. Use a small screwdriver or coin to open the compartment cover.
3. Remove the old CR2032 battery.
4. Insert a new CR2032 battery with the positive (+) side facing up.
5. Replace the compartment cover securely.

Note: Dispose of old batteries responsibly according to local regulations.

Troubleshooting

If you encounter issues with your ES02-USB, refer to the following common problems and solutions:

• Remote not responding:
  • Check the battery in the remote control. Replace it if necessary.
  • Ensure the ES02-USB receiver board is securely connected to the motherboard's USB 2.0 9-pin header.
  • Verify that the Power SW and Reset SW cables are correctly connected to both the Y-cable and the motherboard.
  • Ensure the computer is powered on and the motherboard is receiving power.
• Reduced operating range:
  • Replace the remote control battery.
  • Ensure there are no significant physical obstructions (e.g., thick walls, metal objects) between the remote and the computer.
  • Minimize interference from other 2.4GHz wireless devices (e.g., Wi-Fi routers, cordless phones).
• Computer case buttons not working:
  • Double-check the connections of your computer case's Power SW and Reset SW cables to the ES02-USB Y-cable.
  • Ensure the Y-cable is correctly connected to the motherboard's front panel headers.

Specifications

Warranty and Support

For warranty information and technical support, please visit the official SilverStone Technology website or contact their customer service. Keep your purchase receipt for warranty claims.

Official SilverStone Website: www.silverstonetek.com