SINGER Stitch Sew Quick 2 Handheld Mending Machine Instruction Manual

1. Product Overview

The SINGER Stitch Sew Quick 2 is a compact and portable double stitch mending machine designed for fast repairs to clothing and everyday household items. It operates on all household fabrics, from bedding to curtains, and features an automatic winding function and dual speed control. Its cordless capability allows for flexible use, and a built-in power switch ensures safe management.

2. What's in the Box

Your SINGER Stitch Sew Quick 2 package includes the following items:

• SINGER Stitch Sew Quick 2 Mending Machine
• 2 Threaded Bobbins (one white, one black)
• 1 Machine Needle
• 1 Needle Threader
• 1 Large Spool Pin (for winding)
• 1 Bobbin Pin (for rewinding)

Image: The SINGER Stitch Sew Quick 2 machine in its retail packaging, displaying the machine and its accessories.

3. Parts Diagram

Familiarize yourself with the components of your SINGER Stitch Sew Quick 2 machine:

Image: A detailed view of the SINGER Stitch Sew Quick 2, highlighting various parts such as the handle, ON/OFF button, handwheel, thread guides, tension dial, presser foot lifter, needle clamp screw, needle, needle plate, bobbin case cover, and bobbin case & bottom bobbin.

4. Setup

4.1. Battery Installation

The SINGER Stitch Sew Quick 2 requires 4 AA batteries (not included). Ensure the device is in the OFF position before installing batteries.

1. Locate the battery compartment on the underside of the machine.
2. Open the battery compartment cover.
3. Insert four AA batteries, ensuring correct polarity (+/-).
4. Close the battery compartment cover securely.

Important: Replace all four AA batteries simultaneously. Do not mix alkaline with standard carbon or zinc batteries.

Image: The underside of the SINGER Stitch Sew Quick 2 machine, with the battery compartment visible for battery insertion.

4.2. Initial Run

When operating the device for the first time, run it for 10 seconds, then pause for 5 seconds. After this initial cycle, it can be used regularly.

5. Operating Instructions

5.1. Basic Sewing

The Stitch Sew Quick 2 uses two threads to form a permanent lock stitch, similar to a standard sewing machine.

1. Lift the presser foot and raise the needle by turning the handwheel towards the back of the machine.
2. Ensure both thread ends are pulled approximately 4 inches behind the needle.
3. Place the fabric under the presser foot.
4. Lower the needle into the fabric.
5. Lower the presser foot.
6. Press and release the power button to begin sewing.
7. When finished, press and release the power button to stop sewing.

Image: A hand holding the SINGER Stitch Sew Quick 2 machine, positioned over fabric, demonstrating its handheld operation.

5.2. Speed Control

To adjust the sewing speed:

• Press the speed button once for a faster speed.
• Press it again to return to normal speed.

5.3. Tension Adjustment

Proper thread tension is crucial for a good stitch. Adjust the thread tension dial as follows:

• If the upper tension is too tight (upper thread lies straight along the fabric surface), turn the tension dial counter-clockwise to loosen.
• If the upper tension is too loose (bottom thread lies straight along the fabric surface), turn the tension dial clockwise to tighten.

5.4. Finishing a Seam

When you have completed your sewing:

1. Pull the upper thread loose by hand to prevent the needle from bending when removing the fabric.
2. Raise the needle and presser foot.
3. Pull the fabric towards the back of the machine.
4. Cut both threads approximately 4 inches from the edge of the fabric.

6. Maintenance

6.1. Changing the Needle

Caution: Ensure the power switch is OFF before changing the needle.

1. Raise the needle to its highest position.
2. Hold the needle and loosen the needle clamp screw.
3. Remove the old needle.
4. Insert the new needle into the clamp with the flat side towards the right of the machine. Ensure the eye is straight and facing the right or left of the machine.
5. Push the needle all the way up into the bar before tightening the needle clamp screw.
6. Tighten the needle clamp screw.

7. Winding the Bobbin

To wind a new bobbin:

1. Either slide open the bobbin case cover and remove the empty bobbin, or obtain an empty Class 15 metal bobbin.
2. Insert the bobbin pin into the hole on the top of the machine.
3. Place the empty bobbin onto the bobbin pin.
4. Ensure the thread from the spool to the bobbin is routed through thread guide 1 and the thread tension dial.
5. Pass the thread through the small hole of the bobbin from the inside, pulling about 3 inches of thread through the hole.
6. Hold the thread end tightly.
7. Press down the power button to start winding.
8. Stop after a few coils are wound. Cut the thread end on the top of the bobbin close to the bobbin.
9. Continue winding until the desired amount of thread is wound.
10. Cut the thread 4 inches from the bobbin.
11. Remove the wound bobbin from the bobbin pin.

8. Bobbin Placement

When the bottom bobbin thread is used up or you wish to change thread color:

1. Pull the bobbin cover to the left and remove it.
2. Remove the used bottom bobbin from the bobbin case.
3. Ensure the thread on the bobbin being inserted unwinds in a clockwise direction, as marked on the bobbin case.
4. Place the new bobbin into the compartment with about 3 inches of thread left hanging out.
5. To catch the bobbin thread, raise the presser foot by pulling up the presser foot lifter.
6. Hold the top thread and turn the handwheel towards the back of the machine to make the needle go down and back up.
7. You will see a loop formed by the bobbin thread. Pull the loop to find the end of the bobbin thread.
8. Pull the ends of both threads to the back of the machine.
9. Slide the bobbin case cover back into place.

9. Threading the Needle

To thread the SINGER Stitch Sew Quick 2:

1. Ensure the upper bobbin or spool with thread unwinds in a clockwise direction.
2. Pull the thread from the bobbin/spool through thread guide 1.
3. Slip the thread in between the two discs of the thread tension dial.
4. Pull the thread through thread guide 2 (from back to front).
5. Thread the take-up lever (from back to front).
6. Thread guide 3 (from front to back).
7. Thread guide 4 (down).
8. Raise the needle.
9. Pass the needle threader through the eye of the needle (from left to right).
10. Pass the thread through the eye of the needle threader.
11. Pull the needle threader with the inserted thread through the eye of the needle (from right to left).
12. Remove the needle threader.

10. Troubleshooting

For common issues and solutions, refer to the troubleshooting section in your physical instruction manual. Here are some possible causes for a poor stitch:

• The presser foot is not in the down position.
• The needle is not fully inserted in the needle bar.
• The needle eye is not facing the right or left of the machine.
• The wrong size needle is being used.
• Upper threading is incorrect.
• Lower threading is incorrect.
• The bobbin is not correctly placed in which the bobbin case is blocked for counter-clockwise rotation.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the device by a person responsible for their safety. Children should be supervised to ensure that they do not play with the device.

11. Specifications

12. Official Product Video Guide

For a visual demonstration of the SINGER Stitch Sew Quick 2, including setup, operation, and maintenance, please refer to the official video below:

13. Warranty and Support

For warranty information, product registration, or further technical support, please visit the official SINGER website or contact their customer service. Details can typically be found in the warranty card included with your product or on the manufacturer's website.