1. Introduction
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your Steinel XLED Home 2 S Outdoor LED Floodlight with Motion Sensor. Please read these instructions carefully before initial use and retain them for future reference.
The Steinel XLED Home 2 S is an energy-efficient LED floodlight designed for outdoor use, featuring an integrated 180° infrared motion sensor. It provides bright, warm white illumination for areas such as entrances, courtyards, gardens, and patios.
2. Safety Instructions
- Electrical Installation: Installation must be performed by a qualified electrician in accordance with national wiring regulations and local electrical codes.
- Power Disconnection: Always disconnect the power supply before performing any work on the unit.
- Voltage: Ensure the supply voltage matches the product's specifications (220-240 V / 50-60 Hz).
- Damage: Do not operate the product if it is damaged. Contact qualified service personnel for repairs.
- Modifications: Do not modify the product in any way. Unauthorized modifications can lead to hazards and void the warranty.
- Operating Environment: This product is designed for outdoor use (IP44 rated). Ensure it is installed in a location protected from direct water jets and extreme weather conditions.
3. Package Contents
Verify that all components are present and undamaged upon unpacking:
- Steinel XLED Home 2 S LED Floodlight
- Mounting material (2x screws, 2x wall plugs, 3x spacers, 2x sealing plugs)
- Sensor covers for detection zone adjustment
- Instruction Manual
4. Product Overview
The Steinel XLED Home 2 S is an advanced outdoor LED floodlight featuring a highly efficient LED panel and an integrated motion sensor for automated lighting. Its design allows for flexible adjustment of both the light panel and the sensor.
Figure 1: Front view of the Steinel XLED Home 2 S LED Floodlight. This image shows the main unit with its adjustable LED panel and the motion sensor located beneath.
Figure 2: Technical drawing illustrating the dimensions of the Steinel XLED Home 2 S. The dimensions are approximately 161mm (width) x 180mm (depth) x 218mm (height).
Key Features:
- High Efficiency LED: Consumes only 13.7 W, providing 1550 lumens of warm white light (3000 K).
- Adjustable LED Panel: The LED panel can be flexibly oriented up to 180° to direct light precisely where needed.
- 180° Infrared Motion Sensor: Reliably detects movement up to 10 meters. The sensor can be adjusted vertically by 180° and horizontally by 90°.
- Adjustable Detection Zone: Supplied covers allow for customization of the sensor's detection area.
- Long LED Lifespan: LEDs are designed for a lifespan of 50,000 hours, eliminating the need for frequent bulb changes.
- Network Capability: Up to 10 floodlights can be interconnected for synchronized operation.
5. Installation
The Steinel XLED Home 2 S is designed for wall mounting. For electrical connections, it is strongly recommended to consult a qualified electrician.
Mounting Steps:
- Choose Location: Select a suitable outdoor location for wall mounting, ensuring the desired detection area is covered by the sensor.
- Prepare Wiring: Ensure the power supply is disconnected at the main circuit breaker. Prepare the electrical wires for connection.
- Mount Base Plate: Secure the floodlight's base plate to the wall using the provided screws and wall plugs. Use spacers if necessary to ensure a flush fit or accommodate wiring.
- Connect Electrical Wires: Connect the live (L), neutral (N), and earth (PE) wires to the corresponding terminals on the floodlight. Ensure connections are secure.
- Attach Floodlight: Carefully attach the floodlight unit to the mounted base plate and secure it with the small screw located at the bottom of the light.
- Restore Power: Once installation is complete and all connections are secure, restore power to the circuit.
Figure 3: An installed Steinel XLED Home 2 S floodlight illuminating an outdoor pathway and entrance at night.
6. Operating Instructions
The Steinel XLED Home 2 S features adjustable settings for its motion sensor to customize its operation according to your needs.
Motion Sensor Adjustment:
The motion sensor's settings can be adjusted using the rotary knobs located on the underside of the sensor unit.
- Time Setting (Temporisation): This knob controls how long the light remains on after motion is detected. The adjustable range is typically from 8 seconds to 35 minutes.
- Twilight Setting (Crépuscularité): This knob determines the ambient light level at which the sensor becomes active. The adjustable range is from approximately 2 lux (dark) to 2000 lux (daylight). Set it to a lower lux value for activation only in darker conditions, or a higher value for activation even in brighter conditions.
Adjusting Detection Zone:
The 180° infrared motion sensor can detect movement up to 10 meters. To prevent unwanted activations (e.g., from passing traffic or pets), you can precisely adjust the detection zone.
- Sensor Orientation: The sensor head can be physically rotated vertically by 180° and horizontally by 90° to aim the detection field.
- Detection Zone Covers: Use the provided covers to mask off specific segments of the detection area. Attach these covers to the sensor lens as needed.
Figure 4: Diagram illustrating the motion sensor's detection range and how it covers an area in front of a building. The orange shaded area indicates the sensor's field of view.
7. Maintenance
The Steinel XLED Home 2 S is designed for minimal maintenance. The integrated LEDs have a long lifespan and do not require replacement.
- Cleaning: Periodically clean the floodlight's surface and the sensor lens with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the plastic components.
- Inspection: Regularly inspect the unit for any signs of damage, loose connections, or wear. If any issues are found, disconnect power and consult a qualified professional.
8. Troubleshooting
If you encounter issues with your Steinel XLED Home 2 S, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power supply; Twilight setting too high; Sensor faulty. | Check circuit breaker; Adjust twilight setting to a lower lux value; Contact support. |
| Light stays on continuously. | Continuous motion in detection zone; Time setting too long; Wiring error. | Adjust detection zone with covers; Reduce time setting; Consult electrician. |
| Light turns on without apparent motion. | Detection zone too wide; Environmental factors (e.g., heat sources, small animals). | Adjust sensor orientation; Use detection zone covers; Relocate if necessary. |
| Light flickers or is dim. | Unstable power supply; Internal fault. | Check electrical connections; Contact support. |
9. Specifications
| Feature | Specification |
|---|---|
| Model Number | 33071 |
| Brand | Steinel |
| Power Supply | 220 - 240 V / 50 - 60 Hz |
| Power Consumption | 13.7 Watts |
| Luminous Flux | 1550 lumens |
| Color Temperature | 3000 Kelvin (Warm White) |
| Color Rendering Index (CRI) | 80 |
| LED Lifespan | 50,000 Hours |
| Motion Sensor Type | Infrared (PIR) |
| Detection Angle | 180° |
| Detection Range | Up to 10 meters |
| Time Setting | 8 seconds - 35 minutes |
| Twilight Setting | 2 - 2000 lux |
| Ingress Protection (IP) Rating | IP44 |
| Material | Plastic, Acrylic |
| Dimensions (L x W x H) | 16.1 x 18.0 x 21.8 cm (approx. 7.64 x 7.09 x 6.34 inches) |
| Weight | 0.570 kg (approx. 1.26 lbs) |
| Connectivity | Networkable (up to 10 floodlights) |
10. Warranty and Support
Steinel products are manufactured to high-quality standards. For warranty information, please refer to the documentation provided with your purchase or visit the official Steinel website. In case of technical issues or questions not covered in this manual, please contact Steinel customer support or your local distributor.
For further assistance, you may visit the Steinel Brand Store.
