MISTRAL 8'6 Junior Inflatable Stand Up Paddle Board User Manual

Introduction

Thank you for choosing the MISTRAL 8'6 Junior Inflatable Stand Up Paddle Board. This manual provides essential information for the safe and effective use, setup, maintenance, and storage of your paddle board. Please read this manual thoroughly before using the product and keep it for future reference.

Figure 1: The MISTRAL 8'6 Junior Inflatable Stand Up Paddle Board, fully inflated and ready for use on calm water. This image shows the board's compact size and design suitable for young paddlers.

Safety Information

Always prioritize safety when using your stand up paddle board. Failure to follow these guidelines may result in serious injury or death.

• Wear a Personal Flotation Device (PFD): Always wear a Coast Guard approved PFD suitable for your weight and activity level.
• Check Weather Conditions: Do not paddle in strong winds, currents, or stormy weather. Be aware of local weather forecasts and water conditions.
• Know Your Limits: Paddle within your skill level and physical capabilities. Avoid paddling alone, especially in unfamiliar waters.
• Leash Use: Always attach the leash to your ankle or calf and to the board. This keeps the board close to you if you fall off.
• Avoid Obstacles: Stay clear of rocks, submerged objects, boat traffic, and swimming areas.
• Supervision: Children should always be supervised by an adult when using the paddle board.
• Alcohol and Drugs: Never operate the paddle board under the influence of alcohol or drugs.
• Sun Protection: Use sunscreen, wear appropriate clothing, and stay hydrated.

Package Contents

Upon unpacking, please verify that all components are present and undamaged. If any items are missing or damaged, contact customer support immediately.

• MISTRAL 8'6 Junior Inflatable Stand Up Paddle Board
• Adjustable Paddle
• High-Pressure Hand Pump
• Removable Fin
• Ankle Leash
• Repair Kit (patches, valve wrench)
• Carry Bag

Setup

1. Unpacking and Unrolling

Remove the board from its carry bag and unroll it on a clean, flat surface, free of sharp objects.

2. Inflation

1. Locate the inflation valve on the tail of the board. Ensure the valve pin is in the UP position (closed) to prevent air from escaping. If it's down, press it once to pop it up.
2. Attach the hose of the high-pressure hand pump to the valve by inserting it and twisting clockwise until secure.
3. Begin pumping. The pressure gauge on the pump will not register until the board reaches a certain firmness (typically around 7 PSI).
4. Inflate the board to the recommended pressure of 12-15 PSI (0.8-1.0 bar). Do not overinflate.
5. Once inflated, quickly detach the pump hose and ensure the valve cap is securely fastened to prevent air leakage and protect the valve.

3. Fin Installation

Slide the removable fin into the fin box located on the underside of the board. Secure it with the attached clip or screw, ensuring it is firmly in place. A properly installed fin is crucial for directional stability.

4. Paddle Assembly and Adjustment

1. Assemble the paddle sections by pushing them together until the locking pins engage.
2. Adjust the paddle length. A general rule is that the paddle handle should reach your wrist when your arm is extended overhead. For children, adjust to a comfortable height that allows for efficient paddling without straining.
3. Secure the adjustable section with the clamp or pin.

5. Attaching the Leash

Attach one end of the coiled leash to the D-ring at the tail of the board and the other end to your ankle or calf. This ensures the board remains tethered to you if you fall.

Operating Instructions

1. Getting On the Board

Start in shallow water. Kneel on the center of the board, just behind the handle. Use your hands to paddle initially to get a feel for the board's stability.

2. Standing Up

1. From a kneeling position, place your paddle across the board in front of you.
2. Place your hands flat on the board, shoulder-width apart.
3. Bring one foot forward, then the other, placing them roughly shoulder-width apart in the center of the board.
4. Slowly stand up, keeping your knees slightly bent and your core engaged. Look towards the horizon, not at your feet.

3. Paddling Technique

• Hold the paddle with one hand on the top of the handle and the other on the shaft. The blade should be angled away from you.
• Reach forward with the paddle, insert the blade fully into the water, and pull it back towards your feet.
• Keep your arms relatively straight and use your core muscles to power the stroke.
• To go straight, alternate paddling on both sides of the board.
• To turn, paddle on one side only, or use a sweep stroke (a wide arc from nose to tail) on the side opposite the direction you want to turn.

4. Falling and Remounting

If you fall, try to fall away from the board to avoid hitting it. Use the leash to retrieve your board. To remount, position yourself at the center of the board, grab the handle, and kick your legs to propel yourself onto the board, starting in a prone or kneeling position.

Maintenance

1. Cleaning

After each use, rinse your board with fresh water to remove salt, sand, and dirt. Use a mild soap and soft brush if necessary. Avoid harsh chemicals or abrasive cleaners.

2. Drying

Ensure the board is completely dry before deflating and storing it. Drying prevents mildew and extends the life of the material.

3. Deflation and Storage

1. Remove the fin and store it separately.
2. Open the valve cap and press the valve pin down to the OPEN position. Air will rapidly escape.
3. Roll the board tightly from the nose towards the tail, pushing out any remaining air.
4. Once fully deflated and rolled, secure it with the provided strap and place it in the carry bag.
5. Store the board in a cool, dry place, away from direct sunlight and extreme temperatures.

4. Repair Kit Use

The included repair kit can be used for minor punctures. Clean the area around the puncture, apply adhesive (not always included, may need to be purchased separately) to the patch and the board, and firmly press the patch over the hole. Allow sufficient drying time before re-inflating.

Troubleshooting

Specifications

• Model Number: 117000086
• Brand: MISTRAL
• Dimensions (Inflated): Approximately 8'6" (length) x 30" (width) x 6" (thickness)
• Material: Polychlorure de vinyle (PVC)
• Item Weight: 8 Kilograms (17.6 lbs)
• Maximum Recommended Load: 250 Pounds (113 kg)
• Recommended Inflation Pressure: 12-15 PSI (0.8-1.0 bar)
• Age Range: Child
• Skill Level: Beginner
• Country of Origin: Germany

Warranty and Support

MISTRAL products are manufactured to high-quality standards. For specific warranty details, please refer to the warranty card included with your purchase or visit the official MISTRAL website. If you encounter any issues or require technical assistance, please contact MISTRAL customer support through their official channels.

Keep your proof of purchase for any warranty claims.