TT FLEX Washing Machine Hoses Instruction Manual

1. Introduction

This manual provides essential information for the safe and effective installation, operation, and maintenance of your TT FLEX Washing Machine Hoses. Please read these instructions thoroughly before installation and retain this manual for future reference.

2. Safety Information

Observe the following safety precautions to prevent property damage or personal injury:

• Always turn off the water supply to your washing machine before disconnecting or connecting hoses.
• Ensure all connections are tight to prevent leaks. Do not overtighten, as this can damage the fittings.
• Regularly inspect hoses for signs of wear, cracks, bulges, or leaks. Replace hoses immediately if any damage is observed.
• Do not use hoses for purposes other than their intended use as washing machine supply lines.
• Keep children and pets away from the installation area.

3. Package Contents

Your package should contain the following items:

• 2 x TT FLEX 6FT Black Rubber Washing Machine Hoses (3/4" FHT x 3/4" FHT)

Image: Two coiled black rubber washing machine hoses with brass fittings, as included in the package.

4. Specifications

Image: Visual representation of the hose length (6 feet) and diameter measurements.

Image: Details of the hose construction, highlighting brass nipples, zinc-plated steel nuts, and quality certifications.

5. Setup and Installation

Follow these steps for proper installation of your washing machine hoses:

1. Step One: Check Flat Washers. Ensure that the flat rubber washers are properly seated inside the hose fittings. These washers are crucial for a watertight seal.
2. Step Two: Connect Hoses to Washing Machine. Attach one end of each hose to the corresponding hot and cold water inlet valves on the back of your washing machine. Hand-tighten until snug.
3. Step Three: Connect Hoses to Water Supply. Attach the other end of each hose to the hot and cold water supply valves (faucets) on your wall. Hand-tighten until snug.
4. Step Four: Tighten Connections with a Wrench. Using a wrench, carefully tighten each connection an additional quarter to half turn. Do not overtighten.
5. Step Five: Check for Leaks. Slowly turn on the water supply. Inspect all four connections for any signs of leaks. If a leak is detected, turn off the water, tighten the connection slightly, and recheck.

Image: Step-by-step visual guide for connecting washing machine hoses.

Image: Example of correctly installed washing machine hoses.

6. Operating Instructions

Once the hoses are securely installed and checked for leaks, your washing machine is ready for operation. The hoses will automatically supply hot and cold water to the appliance as needed during wash cycles.

7. Maintenance

To ensure the longevity and safe operation of your TT FLEX washing machine hoses:

• Regular Inspection: Periodically check the hoses for any signs of wear, such as cracks, bulges, kinks, or corrosion on the fittings. It is recommended to inspect them at least once a year.
• Replace as Needed: Hoses should be replaced every 3-5 years, or immediately if any damage is found, even if they appear to be functioning correctly.
• Turn Off Water: If you are going away for an extended period, it is advisable to turn off the water supply to the washing machine to reduce the risk of leaks.
• Cleaning: Clean the exterior of the hoses with a damp cloth if necessary. Do not use harsh chemicals or abrasive cleaners.

Image: Internal construction of the hose, illustrating its durability features.

8. Troubleshooting

If you encounter issues with your washing machine hoses, consider the following:

• Leaks at Connections:
  • Ensure the water supply is off.
  • Check that the rubber washers are correctly seated and not damaged. Replace if necessary.
  • Tighten connections slightly with a wrench. Do not overtighten.
• No Water Flow:
  • Verify that the hot and cold water supply valves are fully open.
  • Check for kinks in the hoses that might restrict water flow.
• Hose Damage:
  • If a hose shows signs of cracking, bulging, or severe wear, it must be replaced immediately to prevent a burst.

9. Warranty

TT FLEX offers a 10-year warranty on these washing machine hoses. This warranty covers defects in materials and workmanship under normal use and service. For warranty claims or further assistance, please refer to the contact information provided by your retailer or the TT FLEX official website.

10. Support

For technical support, product inquiries, or warranty service, please contact TT FLEX customer service through the retailer where the product was purchased or visit the official TT FLEX website for contact details.