Introduction
This instruction manual provides detailed guidance for the setup, operation, and maintenance of your Amplicomms BKR-33 Universal Remote Control. Designed for ease of use, particularly for seniors or individuals with limited motor skills, this remote features large, illuminated buttons and a convenient learning function. Please read this manual thoroughly to ensure proper use and to maximize the functionality of your device.
Product Overview
The Amplicomms BKR-33 is a universal remote control capable of operating up to four different devices, including TVs, stereo systems, SAT receivers, and radios. Its key features include:
- Large, Illuminated Buttons: For enhanced visibility and ease of pressing.
- Learning Function: Allows copying functions directly from your original remote controls.
- Memory Retention: Settings are retained even after battery replacement.
- Ergonomic Design: Comfortable to hold and operate.
Figure 1: Amplicomms BKR-33 Universal Remote Control. This image shows the white remote control with large, clearly labeled buttons for power, numbers, volume, and channel control. The Amplicomms logo is visible at the bottom.
Setup
1. Battery Installation
- Locate the battery compartment on the back of the remote control.
- Open the battery compartment cover.
- Insert two AAA batteries (not included), ensuring correct polarity (+/-).
- Close the battery compartment cover securely.
2. Learning Function (Copying from Original Remote)
The BKR-33 remote learns functions directly from your existing remote controls. This process needs to be done for each button you wish to program.
- Place the Amplicomms BKR-33 and your original remote control on a flat surface, facing each other, with their infrared emitters aligned at a distance of approximately 2-5 cm.
- Press and hold the desired device button (e.g., TV, SAT) on the BKR-33 for approximately 3 seconds until the indicator light flashes slowly.
- Press the button on the BKR-33 that you wish to program (e.g., Power button). The indicator light will now flash rapidly.
- Press and hold the corresponding button on your original remote control (e.g., Power button) until the indicator light on the BKR-33 flashes three times and then stays on. This indicates successful learning.
- Repeat steps 3 and 4 for all other buttons you wish to program for that device.
- To exit learning mode, press the device button again or wait for 10 seconds.
Note: If the indicator light does not flash as described, ensure batteries are fresh and the remotes are properly aligned. Some original remotes may have weaker IR signals, requiring closer proximity or a longer press.
Operating Instructions
Once programmed, operating the Amplicomms BKR-33 is straightforward:
- Device Selection: Press the corresponding device button (e.g., TV, SAT) to select the device you wish to control. The indicator light will illuminate to confirm selection.
- Power Button (⏻): Turns the selected device on or off.
- Number Buttons (0-9, *, #): For direct channel input or other numerical functions.
- Volume Buttons (Volume +, Volume -): Adjusts the volume of the selected device.
- Channel Buttons (Channels ∧, Channels ∨): Changes channels up or down.
- Illumination Button (💡): Activates the backlight for the buttons, improving visibility in low-light conditions.
- Favorite Buttons (♥1, ♥2): These buttons can be programmed for frequently used functions or favorite channels.
Maintenance
- Cleaning: Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Battery Replacement: When the remote's performance degrades, replace the AAA batteries. The remote retains its programming even after battery replacement, so no re-programming is necessary.
- Storage: Store the remote in a dry place, away from direct sunlight and extreme temperatures.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote does not respond. | Dead or incorrectly inserted batteries. | Replace batteries with new AAA batteries, ensuring correct polarity. |
| Learning function fails or is inconsistent. | Remotes not aligned, too far apart, or original remote has a weak IR signal. | Ensure remotes are 2-5 cm apart and IR emitters are aligned. Try holding the original remote button longer. Ensure the BKR-33 is in learning mode. |
| Buttons control the wrong device. | Incorrect device selected. | Press the correct device button (TV, SAT, etc.) before operating. |
| Some functions are not working after programming. | Button not successfully learned or learned incorrectly. | Repeat the learning process for the specific non-working button. |
Specifications
| Brand | Amplicomms |
| Model Number | 906436 |
| Model Name | Universelle Fernbedienung mit Großtasten (Universal Remote Control with Large Buttons) |
| Manufacturer | Audioline GmbH |
| Compatible Devices | TV, stereo system, SAT receiver, radio |
| Maximum Supported Devices | 4 |
| Special Features | Universal, Illuminated buttons, Learning function |
| Connectivity Technology | Infrared |
| Controller Type | Button control |
| Battery Type | AAA (2 required, not included) |
| Product Dimensions | 5 x 2.1 x 18.5 cm |
| Item Weight | 122 g |
| ASIN | B01M6CLPML |
| GTIN | 04250711906436 |
Warranty and Support
The Amplicomms BKR-33 Universal Remote Control comes with a two-year warranty from the date of purchase. Please retain your proof of purchase for warranty claims.
For further assistance or technical support, please refer to the contact information provided with your product packaging or visit the official Amplicomms website.