1. Introduction
The Equinox Microbar Multi System T-Bar is a compact, all-in-one lighting solution designed for various applications. This system includes two LED PAR cans and two RGBW LED effect lights mounted on a powered T-bar, complete with a robust stand and an infrared remote control. A protective carry bag is also included for convenient transport. This manual provides essential information for the safe and efficient operation of your lighting system.
2. Safety Information
- Always connect the unit to a grounded power outlet.
- Ensure the power supply voltage matches the unit's requirements (100-240V, 50/60Hz).
- Do not expose the unit to rain or moisture. Avoid use in wet conditions.
- Do not open the housing; there are no user-serviceable parts inside. Refer all servicing to qualified personnel.
- Avoid direct eye exposure to the light source.
- Ensure adequate ventilation around the unit to prevent overheating.
- Position the stand on a stable, level surface to prevent tipping.
- Keep the unit away from flammable materials.
3. Package Contents
Verify that all items are present in the package:
- Equinox Microbar Multi System T-Bar (with 2 LED PAR cans and 2 RGBW effect lights)
- Robust Lighting Stand
- Infrared Remote Control
- Protective Carry Bag
- Power Cable
- User Manual (this document)
4. Setup
4.1 Assembling the Stand
- Carefully remove the lighting stand from the carry bag.
- Extend the tripod legs of the stand to a stable position. Ensure the legs are fully spread and locked.
- Adjust the height of the stand to your desired level, securing it with the provided locking pin and knob.
4.2 Mounting the T-Bar System
- Place the Equinox Microbar Multi System T-Bar onto the top pole of the assembled stand.
- Secure the T-bar to the stand using the integrated mounting hardware, ensuring it is firmly attached and stable.
- Adjust the angle of the individual LED lights as desired.
Figure 1: Fully assembled Equinox Microbar Multi System T-Bar on its stand.
4.3 Power Connection
- Connect the provided power cable to the power input on the rear of the T-bar.
- Plug the other end of the power cable into a suitable grounded electrical outlet.
- The unit will power on, and the LED display on the rear panel will illuminate.
Figure 2: Rear panel connections including power input and DMX ports.
5. Operating Instructions
The Equinox Microbar Multi System can be controlled via the onboard LED display and push buttons, or using the included infrared (IR) remote control. It also supports DMX control.
5.1 Onboard Control Panel
Use the MENU, UP, DOWN, and ENTER buttons on the rear panel to navigate through the various modes and settings displayed on the LED screen.
- MENU: Cycles through main menu options.
- UP/DOWN: Adjusts values or navigates through sub-menus.
- ENTER: Confirms selection.
5.2 IR Remote Control
The IR remote provides convenient access to common functions. Ensure the remote is pointed towards the front of the T-bar for optimal reception.
Figure 3: Infrared remote control layout.
- ON/OFF: Powers the unit on or off.
- AUTO MIX: Activates automatic program mode.
- SOUND MIX: Activates sound-activated program mode.
- DMX: Switches to DMX control mode.
- PAR JUMP / PAR GRADUAL / PAR FLASH: Controls specific PAR light effects.
- LED COLOR / LED MOTOR / LED SEN: Adjusts color, motor speed (for effect lights), or sound sensitivity.
- +/- Buttons: Adjusts parameters for selected functions.
5.3 Operating Modes
- Automatic Mode: The system cycles through pre-programmed light shows. Select via the onboard display or "AUTO MIX" on the remote.
- Sound-Activated Mode: The lights react to music or sound. Select via the onboard display or "SOUND MIX" on the remote. Adjust sensitivity using the remote or onboard controls.
- Color Mode: Allows selection of static colors or color changing sequences.
- DMX Mode: For advanced control using a DMX controller. Connect a DMX cable from your controller to the DMX IN port on the T-bar. Set the DMX address using the onboard display. Refer to the DMX channel chart (not provided in this manual, typically found in a separate DMX guide) for specific control parameters.
6. Maintenance
6.1 Cleaning
- Disconnect the unit from power before cleaning.
- Use a soft, lint-free cloth to wipe down the exterior of the unit.
- For lenses, use a specialized lens cleaning solution and cloth to avoid scratches.
- Do not use abrasive cleaners or solvents.
6.2 Storage
When not in use, store the Equinox Microbar Multi System in its protective carry bag in a cool, dry place, away from direct sunlight and extreme temperatures.
Figure 4: Protective carry bag for transport and storage.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Power cable disconnected; no power from outlet. | Check power cable connection; test outlet with another device. |
| Lights not responding to IR remote | Remote batteries low/dead; remote not pointed correctly; obstruction. | Replace remote batteries; ensure clear line of sight to the T-bar's front sensor. |
| Sound-activated mode not working | Microphone sensitivity too low; no sound input. | Increase sound sensitivity via remote or onboard controls; ensure music is playing loudly enough near the unit. |
| DMX control issues | Incorrect DMX address; faulty DMX cable; DMX controller issue. | Verify DMX address setting; check DMX cable connections; test with a different DMX cable or controller. |
8. Specifications
| Feature | Detail |
|---|---|
| Power Consumption | 55 W |
| Power Supply | 100 ~ 240 V, 50/60 Hz |
| Dimensions (without stand) | 200 x 750 x 165 mm |
| Weight | 5.7 kg |
| Control Modes | Auto, Sound Active, Color, DMX, IR Remote |
| Model Number | EQLED136 |
9. Warranty and Support
For warranty information and technical support, please refer to the documentation provided at the point of purchase or contact your local Equinox dealer. Keep your proof of purchase for any warranty claims.
