1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Okin Bed Motor Hand Control. Please read this manual thoroughly before use to ensure proper function and longevity of the product.
2. Product Overview
The Okin 6-Button 5-Pin Hand Control is designed as a replacement remote for adjustable hospital beds equipped with an OKIN Okimat II Motor. It provides intuitive control over various bed adjustments.
Figure 2.1: Okin 6-Button 5-Pin Hand Control. This image shows the full view of the black hand control with its coiled cord and 5-pin connector.
Figure 2.2: Okin Hand Control with Integrated Handle. This image displays the side view of the hand control, highlighting the built-in handle designed for easy stowaway.
Video 2.3: Overview of the Okin 6-Button Hospital Bed Remote Hand Control. This video demonstrates the remote's features, including its 6-button operation, handle for easy stowaway, premium coiled cable, and 5-pin 90-degree connector. It also clarifies that it will not replace a power recliner hand control.
Key Features:
- 6-button operation for comprehensive bed adjustments.
- Integrated handle for convenient stowaway.
- Durable coiled cable for extended reach and flexibility.
- 5-pin 90-degree connector for secure attachment.
- Designed specifically for Okin Okimat II motors in hospital beds.
3. Setup
Before connecting the hand control, ensure the bed's power supply is disconnected from the wall outlet to prevent accidental operation or electrical hazards.
- Locate the existing hand control cable connection point on your adjustable bed's motor. This is typically a 5-pin circular port.
- Align the 5-pin connector of the new Okin hand control with the port on the motor. The connector is designed with a 90-degree angle for easy insertion.
- Gently push the connector firmly into the port until it is fully seated. Do not force the connection.
- Once connected, restore power to the bed by plugging the power supply back into the wall outlet.
- Test all functions of the hand control to ensure proper operation.
Figure 3.1: Detail of the 5-pin 90-degree connector. This image highlights the specific connector type required for compatibility with Okin Okimat II motors.
4. Operating Instructions
The Okin hand control features six buttons for adjusting your bed's position. Refer to the diagram below for button functions.
Figure 4.1: Hand Control Button Layout and Functions. This image clearly labels each button's purpose: Head Up, Head Down, Foot Up, Foot Down, and two buttons for operating Head & Foot together.
- Head Up/Down: Use the top pair of buttons to raise or lower the head section of the bed.
- Foot Up/Down: Use the middle pair of buttons to raise or lower the foot section of the bed.
- Head & Foot Together: The bottom two buttons operate both the head and foot sections simultaneously for a combined adjustment.
Press and hold the desired button until the bed reaches the desired position. Release the button to stop movement.
5. Maintenance
To ensure the longevity and proper functioning of your hand control, follow these simple maintenance guidelines:
- Keep the hand control clean by wiping it with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
- Do not expose the hand control to excessive moisture or liquids.
- Avoid dropping the hand control or subjecting it to strong impacts.
- Regularly inspect the coiled cable and connector for any signs of wear, fraying, or damage. If damage is observed, discontinue use and seek a replacement.
- Store the hand control using its integrated handle when not in use to prevent damage or entanglement.
6. Troubleshooting
If you experience issues with your Okin Bed Motor Hand Control, please review the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Hand control is unresponsive. |
|
|
| Only some buttons work. |
|
|
Important Note: This hand control is specifically designed for Okin Okimat II motors. It will not replace a power recliner hand control or other non-compatible systems. Always verify your bed's motor and connector type before purchasing a replacement.
7. Specifications
| Attribute | Detail |
|---|---|
| Brand | Okin |
| Model | Okimat II Hand Control (Replacement) |
| Connector Type | 5-Pin, 90-Degree Angle |
| Number of Buttons | 6 |
| Cord Length | Approximately 6.6 feet |
| Item Weight | 9.1 ounces |
| Product Dimensions | 9.8 x 4.6 x 3.5 inches |
8. Warranty and Support
For any questions, technical assistance, or warranty inquiries regarding your Okin Bed Motor Hand Control, please contact the seller or manufacturer directly. Ensure you have your purchase details available when contacting support.
It is recommended to verify compatibility with your specific bed model and motor type (Okimat II) before purchase to avoid issues.
