Introduction
This manual provides detailed instructions for the safe and efficient operation of your Dragonhawk LCD Dual Tattoo Machine Power Supply, Model P076. Please read this manual thoroughly before use to ensure proper setup and to maximize the lifespan of your equipment.
Safety Information
- Always ensure the power supply is disconnected from the main power source before connecting or disconnecting any components.
- Do not expose the power supply to moisture or extreme temperatures.
- Avoid dropping the unit or subjecting it to strong impacts.
- Only use the provided power plug and compatible accessories.
- This device is intended for professional use by trained individuals.
- Do not attempt to disassemble or repair the unit yourself. Refer to qualified service personnel.
Package Contents
Verify that all items are present in your package:
- 1 x Dragonhawk LCD Dual Tattoo Machine Power Supply (Model P076)
- 1 x Power Plug (suitable for your region)
- 1 x Dragonhawk Foot Pedal
- 1 x Clip Cord
Product Overview
The Dragonhawk P076 Power Supply is designed to provide stable and consistent power output for tattoo machines. Its compact size and user-friendly interface make it suitable for various tattooing environments.
Image: Dragonhawk P076 Power Supply shown with its retail packaging.
Key Features:
- Quick and accurate voltage adjustments.
- Smooth, consistent power output for enhanced machine reliability.
- Compact and portable design (Net Weight: 145g, Dimensions: 90*87*32.5mm).
- Overvoltage protection for safety.
- Anti-fatigue mode for extended use.
Image: The power supply with text indicating "Mini Power", "Portable Mini", "Switch on/off", "Overvoltage protecting", "Net Weight: 145g", and "Cubage: 90*87*32.5mm".
Setup Instructions
- Connect Power: Plug the provided power plug into the power supply's input port (located at the back) and then into a suitable electrical outlet. The LCD display should illuminate.
- Connect Foot Pedal: Insert the foot pedal's connector into the designated foot pedal port on the front of the power supply. This port is typically marked with a foot pedal icon.
- Connect Clip Cord: Insert one end of the clip cord into the clip cord port on the front of the power supply. This port is typically marked with a coil machine icon or similar. Connect the other end of the clip cord to your tattoo machine.
Image: Front view of the power supply showing the two input jacks, the digital voltage display, and the rotary knob.
Image: Back view of the power supply, illustrating the power input socket and regulatory markings.
Operating Instructions
- Power On/Off: Once connected to power, the unit is typically in standby. Press the rotary knob to turn the power supply on or off.
- Adjusting Voltage: Rotate the knob clockwise to increase the voltage and counter-clockwise to decrease it. The current voltage will be displayed on the LCD screen.
- Anti-Fatigue Mode: To activate the anti-fatigue mode, press and hold the rotary knob for a few seconds. This mode allows the machine to run continuously without needing to keep the foot pedal pressed. Press the knob again to deactivate.
Image: The power supply with an illustration showing how to press the knob to switch it on/off and activate anti-fatigue mode.
Maintenance
- Cleaning: Wipe the exterior of the power supply with a soft, dry cloth. Do not use abrasive cleaners or immerse the unit in liquids.
- Storage: Store the power supply in a cool, dry place away from direct sunlight and extreme temperatures when not in use.
- Cable Care: Regularly inspect all cables (power, foot pedal, clip cord) for any signs of wear or damage. Replace damaged cables immediately.
Troubleshooting
- No Power:
- Ensure the power plug is securely connected to both the power supply and the electrical outlet.
- Check if the electrical outlet is functional.
- Verify the power supply is switched on (press the rotary knob).
- Machine Not Running:
- Check all connections: power supply to outlet, foot pedal to power supply, clip cord to power supply, and clip cord to tattoo machine.
- Ensure the voltage is set appropriately for your machine.
- If using a foot pedal, ensure it is functioning correctly.
- If in anti-fatigue mode, ensure it is activated correctly.
- Inconsistent Power Output:
- Inspect all cables for damage or loose connections.
- Ensure the power supply is on a stable surface and not overheating.
Specifications
| Brand | Dragonhawk |
| Model Number | P076 (longyingyhbe) |
| Color | Black |
| Material | Aluminum |
| Form Factor | Box |
| Output Voltage | 18 Volts (DC) |
| Connector Type | 3 Pin XLR, Barrel Connector, 3.5 mm Jack |
| Net Weight | 145 gram |
| Dimensions | 90*87*32.5mm |
Warranty and Support
Dragonhawk provides coverage for this product. For any inquiries or support needs, please reach out through Amazon's messaging system. For video tutorials, setup guides, and professional tips, visit the official Dragonhawk YouTube channel at Youtube.com/@Dragonhawkofficial.
