1. Introduction
The Eaton CHSPT2SURGE is a Type 2 Surge Protective Device (SPD) designed to provide whole-home AC power protection. This device universally connects to any manufacturer’s load center (breaker box) and features quick-connect cable protection modules for easy mounting. It is suitable for both indoor and outdoor use, housed in a NEMA 4 rated enclosure.
This manual provides essential information for the safe and correct installation, operation, and maintenance of your Eaton CHSPT2SURGE surge protector.
Key Features:
- AC power protection for your entire home.
- Universal compatibility with any load center.
- Quick-connect design for simplified installation.
- LED status indicators for operational verification.
- Durable NEMA 4 rated enclosure for indoor/outdoor use.
2. Important Safety Information
WARNING: Installation of this device involves working with high voltage electricity. Improper installation can result in serious injury, death, or property damage. This product must be installed by a qualified electrician in accordance with all national and local electrical codes.
- Always turn off all power to the main breaker panel before attempting any installation or maintenance.
- Verify that power is off using a voltage sensing device before proceeding.
- Do not attempt installation if you are not familiar with electrical wiring and safety procedures.
- Ensure the installation environment is dry and free from obstructions.
- Follow all instructions in this manual precisely.
3. Package Contents
The Eaton CHSPT2SURGE package includes:
- 1 x Eaton CHSPT2SURGE Hardwire Surge Protection Device
4. Installation (Setup)
The Eaton CHSPT2SURGE is designed for connection to the load side of the main service disconnect within a load center (breaker box) through a dedicated circuit breaker. Refer to the National Electrical Code (NEC) guidelines for proper installation.
Installation Steps:
- Power Disconnection: Turn off the main power supply to your electrical panel at the utility meter or main disconnect. Confirm zero voltage with a multimeter.
- Mounting: The surge protector can be attached to the outside of any manufacturer’s load center. Choose a suitable location near the panel.
- Breaker Installation: Install a dedicated 2-pole, 15-amp circuit breaker in your load center. It is recommended to install this breaker as close as possible to the main incoming power wires in the panel to ensure the surge protector is the first point of protection.
- Wiring Connections: The CHSPT2SURGE unit has four wires:
- Connect the green wire to the ground bar in the load center.
- Connect the white wire to the neutral (common) bar in the load center.
- Connect the remaining two wires (typically red and black) separately to each pole of the newly installed 2-pole, 15-amp circuit breaker.
- Secure Connections: Ensure all wire connections are tight and secure.
- Panel Closure: Carefully replace the load center cover.
- Power Restoration: Restore power to the main breaker panel.
Visual Aid: Product with Wires
Image showing the Eaton CHSPT2SURGE surge protector with its connected wires (green, white, red, black) ready for installation into a breaker panel.
Another view of the Eaton CHSPT2SURGE, highlighting the wiring harness extending from the unit.
Side perspective of the Eaton CHSPT2SURGE, showing the conduit connection point and the bundled wires.
Top-down view of the Eaton CHSPT2SURGE, providing a clear look at the wire colors and their entry point into the device.
5. Operation
Once properly installed and power is restored, the Eaton CHSPT2SURGE operates automatically to protect your home from power surges.
Status Indicators:
The unit features LED status indicators on its front panel. These indicators provide visual confirmation of the device's operational status.
Front view of the Eaton CHSPT2SURGE, showing the 'STATUS INDICATORS' section with two circular lights.
- Both LEDs Lit (Green): This indicates that the surge protector is functioning correctly and providing full protection.
- One or Both LEDs Off: If one or both LEDs are not lit, it indicates that the surge protector has absorbed a significant surge and may no longer be providing full protection. In this event, the unit should be inspected and potentially replaced.
Official Product Video: Surge Protector Status
This video demonstrates the LED status indicators on the Eaton CHSPT2SURGE, showing how to verify if the unit is actively protecting your home's electrical system.
6. Maintenance
The Eaton CHSPT2SURGE is designed to be maintenance-free. It contains no serviceable parts. Regular maintenance is limited to visual inspection.
Inspection:
- Periodically check the LED status indicators on the front of the unit. Ensure both LEDs are lit green.
- Visually inspect the unit for any signs of physical damage, such as cracks, discoloration, or loose connections.
- If any damage is observed or if the LEDs are not lit, contact a qualified electrician for inspection and potential replacement.
7. Troubleshooting
This section addresses common issues you might encounter with your Eaton CHSPT2SURGE surge protector.
Problem: Status LEDs are off.
Possible Cause: The surge protector has absorbed a significant power surge and is no longer providing protection, or there is a power issue to the unit.
Solution:
- First, check the dedicated 2-pole, 15-amp circuit breaker connected to the surge protector in your load center. Ensure it is in the 'ON' position. If it is tripped, reset it.
- If the breaker is on and the LEDs remain off, the surge protector has likely reached its end of life due to absorbing a surge. In this case, the unit needs to be replaced. Contact a qualified electrician for replacement.
- If you suspect a wiring issue, immediately turn off power to the panel and consult a qualified electrician.
8. Specifications
| Feature | Specification |
|---|---|
| Brand | Eaton |
| Model | CHSPT2SURGE |
| Type | Type 2 SPD (Surge Protective Device) |
| Enclosure Rating | NEMA 4 |
| Phase | Single Phase |
| Voltage Rating | 120/240 VAC |
| Frequency | 60 Hz |
| Maximum Continuous Operating Voltage (MCOV) | 150 V L–N, 300 V L–L |
| Voltage Protection Rating (VPR) | 600 V L–N, 1000 V L–L, 800 V N–G, 600 V L–G |
| Nominal Discharge Current (In) | 5 kA |
| Surge Current Capacity | 22 kA |
| Surge Current Capacity, Per Phase Rating | 36 kA (L1–N 18 kA, L1–G 18 kA, L2–N 18 kA, L2–G 18 kA) |
| Circuit Breaker Type (Recommended) | 2-pole, 15-amp |
| Mounting Type | Wall Mount |
| Item Weight | 13.44 ounces |
| Included Components | Hardwire Surge Protection Device |
| Country of Origin | China |
9. Warranty and Support
For warranty information and technical support, please refer to the documentation included with your product or visit the official Eaton website. It is recommended to register your product upon purchase to facilitate any future warranty claims.
If you require assistance with installation, troubleshooting, or have questions regarding the product's performance, please contact Eaton customer support or a qualified electrician.
