1. Introduction
This manual provides instructions for the proper installation, operation, and maintenance of your Lampa N15046 Aluminum Roof Bars. These roof bars feature an elegant design with an anodized aluminum tubular profile, ready for the insertion of quick 'T' fittings in the upper channel. Please read these instructions carefully before installation and use to ensure safety and optimal performance.
Figure 1.1: Lampa N15046 Aluminum Roof Bars.
Product Overview:
- Anodized aluminum tubular profile.
- Designed for quick 'T' fitting insertion.
- Rubber base for load support.
- Complete anti-theft lock system.
- Pre-assembled for quick mounting.
2. Safety Information
WARNING: Improper installation or use can lead to serious injury or property damage.
- Always ensure the roof bars are securely fastened before driving.
- Do not exceed the maximum load capacity of 75 kg (165 lbs).
- Distribute the load evenly on the roof bars.
- Regularly check all fasteners and connections, especially after driving on rough roads or at high speeds.
- Be aware of the increased height and width of your vehicle when roof bars are installed, especially when entering garages or low-clearance areas.
- This product is only for use on vehicles with raised roof rails.
Figure 2.1: Illustration of a raised roof rail, indicating compatibility requirement. These roof bars are designed exclusively for vehicles equipped with raised roof rails, as depicted in the image.
3. Setup and Installation
The Lampa N15046 roof bars are pre-assembled for quick installation. Follow these steps for secure mounting:
- Identify Vehicle Compatibility: Ensure your vehicle has raised roof rails. Refer to Figure 2.1 for an example of compatible roof rails.
- Unpack Components: Remove the roof bars from their packaging. Verify all components are present.
- Adjust Length (if necessary): The roof bars come in various sizes (S, M, L, XL) to fit different vehicle widths. Adjust the length of the bars to match the width of your vehicle's roof rails. The maximum lengths are:
- S: max 100.5 cm
- M: max 112.5 cm
- L: max 119.5 cm
- XL: max 132.5 cm
- Position Roof Bars: Place the roof bars onto your vehicle's raised roof rails. Ensure they are evenly spaced and parallel to each other.
- Secure Clamps: Engage the clamping mechanism around the raised roof rails. The rubber base of the support should make firm contact with the rail.
- Tighten Fasteners: Use the provided tool (e.g., Allen key/brucola mentioned in a review) to tighten all fasteners until the roof bars are firmly secured to the rails. Do not overtighten.
- Engage Anti-theft Lock: Utilize the complete anti-theft lock system to secure the roof bars to prevent unauthorized removal.
- Final Check: Before driving, gently pull and push on each roof bar to confirm it is securely attached and does not move.
Figure 3.1: Dimensional diagram of the Lampa N15046 roof bars, illustrating the height, foot width, and adjustable maximum lengths for different sizes (S, M, L, XL).
Figure 3.2: A close-up view of the Lampa N15046 aluminum roof bars, highlighting the design and construction of the bars and their mounting feet.
4. Operating Instructions
Once installed, your Lampa N15046 roof bars are ready for use. Observe the following guidelines:
- Load Capacity: Do not exceed the maximum load capacity of 75 kg (165 lbs). This includes the weight of the roof bars themselves and any accessories.
- Load Distribution: Distribute the weight of your cargo as evenly as possible across both roof bars. Secure items to prevent shifting during transit.
- Securing Cargo: Use appropriate straps, nets, or other securing devices to firmly attach your cargo to the roof bars. Ensure no part of the cargo obstructs your view or interferes with vehicle operation.
- Driving Considerations:
- Adjust your driving speed to suit road conditions and the load carried.
- Be aware that the vehicle's center of gravity will be higher, affecting handling, especially when cornering or in crosswinds.
- Increased wind resistance may lead to higher fuel consumption.
- Accessory Compatibility: The anodized aluminum tubular profile is designed for the insertion of quick 'T' fittings, allowing for easy attachment of various roof rack accessories (e.g., bike carriers, ski carriers, roof boxes).
5. Maintenance
Regular maintenance ensures the longevity and safe operation of your roof bars:
- Cleaning: Clean the aluminum bars and plastic components with mild soap and water. Avoid abrasive cleaners or solvents that could damage the finish.
- Inspection: Periodically inspect all parts for signs of wear, damage, or corrosion. Pay close attention to the clamping mechanisms, rubber bases, and locking system.
- Fastener Check: Re-tighten all mounting bolts and fasteners regularly, especially after the first few uses and before long trips.
- Lubrication: If the locking mechanism becomes stiff, apply a small amount of graphite lubricant to the keyhole.
- Storage: If not in use for extended periods, consider removing the roof bars and storing them in a dry, protected area to prolong their lifespan.
6. Troubleshooting
This section addresses common issues you might encounter:
- Issue: Roof bars feel loose after installation.
Solution: Re-check all fasteners. Ensure they are tightened securely according to the installation instructions. Verify that the rubber bases are properly seated on the vehicle's raised roof rails.
- Issue: Excessive wind noise during driving.
Solution: Wind noise can be common with roof bars. Ensure the bars are positioned correctly and not twisted. Check if any accessories are contributing to the noise. Some users report noise above 80 km/h (50 mph); this can be a characteristic of roof bars. Consider aerodynamic fairings if noise is a significant concern, though not included with this product.
- Issue: Anti-theft lock is stiff or not working.
Solution: Apply a small amount of graphite lubricant into the keyhole and work the key gently. Ensure no debris is obstructing the mechanism.
- Issue: Difficulty attaching accessories to the T-channel.
Solution: Ensure you are using quick 'T' fittings compatible with the standard aluminum profile. Check for any obstructions within the channel.
7. Specifications
| Feature | Detail |
|---|---|
| Model Number | N15046 |
| Brand | Lampa |
| Material | Aluminum |
| Product Dimensions (L x W x H) | 7.5 x 6.5 x 130 cm (2.95 x 2.56 x 51.18 inches) |
| Item Weight | 3.15 kg (6.94 lbs) |
| Maximum Load Capacity | 75 kg (165 lbs) |
| Vehicle Service Type | Car |
| Mounting Type | Roof Bars (for raised roof rails) |
| Foldable | No |
| Anti-theft Lock | Included |
8. Warranty Information
Specific warranty details for the Lampa N15046 Aluminum Roof Bars are not provided in this manual. Please refer to the product packaging or contact the retailer/manufacturer directly for information regarding warranty coverage and terms.
9. Customer Support
If you have any questions, require assistance with installation, or encounter issues not covered in this manual, please contact your point of purchase or the manufacturer, Lampa, for support.
For further information, you may visit the official Lampa website or consult the product page where you purchased the item.
