BN-LINK BND-60/U48

Download PDF
Contents

BN-LINK Heavy Duty 60-Minute in-Wall Spring Wound Countdown Timer Switch User Manual

Model: BND-60/U48 | Brand: BN-LINK

Product Overview

The BN-LINK Heavy Duty 60-Minute in-Wall Spring Wound Countdown Timer Switch is designed to automatically turn off connected devices after a selected time, up to 60 minutes. This mechanical timer switch is ideal for controlling various electrical loads such as lamps, fans, and other appliances. It is engineered for easy installation in place of an existing wall switch and does not require a neutral wire.

  • Automatically turns off after selected time, up to 60 minutes.
  • Directly wires into a standard light switch (standard toggle or decorator plate).
  • Easily installs in place of existing wall switch, fits any single or multi-gang decorator or toggle switch plate.
  • Works with lamps, fans, and other appliances.
  • Ratings: 125-Volt, 60 Hz./20-Amp, 2500-Watt resistive/8-Amp, 1000-Watt tungsten/5-Amp, 625 W ballast, 1 HP.
  • Wall Plate Included.
BN-LINK 60-Minute in-Wall Spring Wound Countdown Timer Switch

Figure 1: Front view of the BN-LINK 60-Minute in-Wall Spring Wound Countdown Timer Switch with a white faceplate.

Package Contents

Verify that all components are present before beginning installation.

Components included with the BN-LINK timer switch

Figure 2: The package includes the timer switch, a free wall plate, wire nuts, and replaceable white and black knobs.

Setup and Installation

Important Safety Information: Always turn off power at the circuit breaker or fuse box before installing or uninstalling any electrical device. Failure to do so may result in serious injury or death.

  1. Turn Off Power: Locate your circuit breaker panel and turn off the power to the switch you are replacing. Verify power is off using a voltage tester.
  2. Uninstall Current Device: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch.
  3. Choose Faceplate and Knob: The timer comes with both white and silver metallic faceplates, and black and white knobs. You can customize the appearance before installation.
    • To change the knob or faceplate, first firmly pull off the existing knob.
    • Twist the washer off the timer. If it's too tight, use a flathead screwdriver or key to loosen it.
    • Lift off the current faceplate, then place the desired faceplate by pushing it onto the timer.
    • Screw the washer back on securely.
    • Push the new knob onto the timer, ensuring the arrow on the knob faces upwards.
  4. Wiring: This timer requires a hot wire and a load wire in your wallbox. It does not require a neutral wire.
    Wiring diagram for BN-LINK timer switch

    Figure 3: Wiring diagram showing connection of hot and load wires to the timer. Use wire nuts to securely twist together the hot wire from the wallbox to one black wire of the timer, and the load wire from the wallbox to the other black wire of the timer. The order of the black wires from the timer does not matter.

    Use the provided wire nuts to securely connect the wires. Twist the hot wire from your wallbox to one of the black wires from the timer. Then, twist the load wire from your wallbox to the other black wire from the timer. The specific black wire from the timer connected to either the hot or load wire does not affect functionality.

  5. Mounting: Carefully insert the timer into the wallbox, ensuring no wires are pinched. Be sure the faceplate is oriented correctly (not upside down). Screw the timer into the wallbox using the provided screws.
  6. Attach Outer Wallplate: Place the outer wallplate over the installed timer and screw it in.
  7. Restore Power: Turn the power back on at the circuit breaker.

Video 1: Official BN-LINK installation guide for the 60-Minute in-Wall Spring Loaded Countdown Timer. This video demonstrates the full installation process from unboxing to final setup.

Operating Instructions

The BN-LINK timer is simple to operate:

  1. Setting the Timer: To set and start the timer, simply turn the dial clockwise to the desired time. The timer can be set for any duration from 2 to 60 minutes.
  2. Automatic Shut-off: Once set, the timer will begin counting down. When the countdown finishes, the power to the connected device will automatically turn off.
  3. Ending Timer Early: To end the timer early and turn off the power, twist the dial counter-clockwise until the timer reaches the "OFF" position.
BN-LINK timer switch in a bathroom setting, highlighting automatic shut-off

Figure 4: The timer automatically turns off after the selected time, saving energy and money.

Maintenance

The BN-LINK timer switch is designed for minimal maintenance. Keep the device and wall plate clean by wiping with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure the device is free from dust and debris to maintain optimal performance.

Troubleshooting

If you experience issues with your BN-LINK timer switch, consider the following:

  • Timer Not Working/No Power:
    • Ensure power is restored at the circuit breaker.
    • Verify that both a hot and load wire are present in your wallbox and correctly connected to the timer's black wires. This timer requires both for operation.
    • Check wire connections for looseness. Re-tighten wire nuts if necessary.
  • Timer Stops Ticking/Lights Stay On:
    • This can indicate an issue with the internal mechanical mechanism. If the timer stops ticking before reaching "OFF" and the lights remain on, the unit may be faulty.
    • Ensure the connected load does not exceed the timer's maximum ratings (2500W Resistive, 1000W Tungsten, 625W Ballast, 1 HP). Overloading can cause malfunction.
  • Knob/Faceplate Issues:
    • If the knob is loose or spins freely, ensure the washer beneath it is securely screwed on.

Specifications

FeatureDetail
Operation ModeON-OFF
Current Rating20 Amps
Operating Voltage125 Volts
Contact TypeNormally Open
Connector TypeWire Connect
BrandBN-LINK
TerminalThrough Hole
Item Dimensions (L x W x H)4.1 x 2 x 2 inches
Circuit Type1-way
Actuator TypeRotary
Contact MaterialMetal
International Protection RatingIP00
Number of Positions1
Lower Temperature Rating5 Degrees Fahrenheit
Upper Temperature Rating122 Degrees Fahrenheit
Control MethodTouch
Connectivity ProtocolX-10
ColorWhite or Silver
Wattage2500 watts
Unit Count1.0 Count
Item Weight5.6 ounces
Country of OriginChina
Model NumberBND-60/U48
SizeOne Hour
StyleMechanical Countdown Timer Switch
Horsepower1 hp
Item Package Quantity1
Included ComponentsFace Plate
Batteries Included?No
Batteries Required?No

Warranty and Support

For detailed warranty information or further support, please refer to the official user manual provided with your product or visit the BN-LINK Store on Amazon.

An electronic version of the user manual is available for download: User Manual (PDF).

© 2025 BN-LINK. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.