PowerA Charge & Display Station for PlayStation VR Instruction Manual

Introduction

The PowerA Charge & Display Station is designed to provide a secure and organized solution for your PlayStation VR headset, DUALSHOCK 4 controller, and PlayStation Move controllers. This station allows for simultaneous charging of one DUALSHOCK 4 controller and two PlayStation Move controllers, while also serving as a dedicated display stand for your PlayStation VR headset. This manual provides essential information for proper setup, operation, and maintenance of your device.

Package Contents

• PowerA Charge & Display Station
• AC Power Adapter

Safety Information

• Read all instructions before operating the device.
• Keep the device away from water or excessive moisture.
• Do not attempt to disassemble or modify the device.
• Use only the provided AC power adapter.
• Ensure proper ventilation around the device during operation.
• Place the station on a stable, flat surface to prevent tipping.

Setup

1. Unpack the Station: Carefully remove all components from the packaging.
2. Assemble the Station: Connect the vertical stand to the base unit. Ensure it clicks securely into place.
3. Connect Power: Insert the small end of the AC power adapter into the power input port located at the rear of the station's base.
4. Route Power Cable: Utilize the cable management grooves on the underside of the base to route the power cable neatly. There are grooves for rear, left, and right exits.
5. Plug into Outlet: Plug the AC power adapter into a standard wall outlet.

The back of the station, featuring the power input and integrated cable management channels to keep your setup tidy.

Side profile of the Charge & Display Station, illustrating the support structure for the PSVR headset and the charging docks for controllers.

Operating Instructions

1. Displaying the PSVR Headset:
   • Gently place your PlayStation VR headset onto the designated cradle at the top of the station.
   • Adjust the headset's band to ensure a secure and stable fit on the stand. This helps prevent accidental slipping.
   • Route the headset's cable around the stand for organized storage.
2. Charging DUALSHOCK 4 Controller:
   • Align the DUALSHOCK 4 controller with the charging port on the front-left dock of the station.
   • Press the controller down firmly onto the spring-loaded connector until it seats properly.
   • A light indicator on the controller will illuminate, confirming that charging has begun.
3. Charging PlayStation Move Controllers:
   • Insert each PlayStation Move controller into its respective charging slot on the front-right of the station.
   • Ensure the controllers are fully seated in the docks for a proper connection.
   • The indicator lights on the Move controllers will show their charging status.

The PowerA Charge & Display Station, fully assembled and ready to hold and charge your PlayStation VR headset, DUALSHOCK 4 controller, and PlayStation Move controllers.

The PlayStation VR headset positioned on its dedicated stand. Adjust the headset band for a secure fit on the display cradle.

Detail of the DUALSHOCK 4 controller charging dock. Ensure the controller is firmly seated for proper connection and charging.

Detail of the PlayStation Move controller charging docks. Place controllers securely into the slots for charging.

Maintenance

• Cleaning: Disconnect the power adapter before cleaning. Use a soft, dry cloth to wipe the surface of the station. Do not use abrasive cleaners or solvents.
• Storage: When not in use for extended periods, store the station in a cool, dry place.

Troubleshooting

• Controllers Not Charging:
  • Ensure the power adapter is securely connected to both the station and the wall outlet.
  • Verify that controllers are properly seated in their respective charging docks. For DUALSHOCK 4, ensure it is pressed down firmly onto the spring-loaded connector.
  • Check for any obstructions or debris in the charging ports.
• PSVR Headset Slips Off Stand:
  • Ensure the PSVR headset's adjustable band is tightened to its default or a smaller size when placed on the stand. A loose band may cause the headset to slip.
  • Confirm the station is on a stable, level surface.

Specifications

• Model Number: 1426810-01
• Product Dimensions: 13.4 x 9.5 x 5.6 inches
• Item Weight: 1.88 pounds
• Manufacturer: PowerA
• Compatibility: PlayStation VR Headset, DUALSHOCK 4 Controller, PlayStation Move Controllers

Warranty and Support

For warranty information and technical support, please refer to the official PowerA website or contact their customer service directly. Keep your proof of purchase for warranty claims.