PuraFlame EF45D

Download PDF
Contents

PuraFlame Western Electric Fireplace Insert

Model: EF45D

Brand: PuraFlame

Introduction

Thank you for choosing the PuraFlame Western Electric Fireplace Insert. This manual provides essential information for the safe operation, installation, and maintenance of your new electric fireplace. Designed to offer the ambiance of a traditional fireplace without the hassle of cleaning dust or ashes, this unit features realistic flame effects and supplemental heating capabilities.

Important Safety Information

Please read all instructions before using this appliance. Failure to follow these instructions may result in electric shock, fire, or personal injury.

  • Ensure the fireplace is plugged into a 120V outlet. This unit CANNOT be hard-wired.
  • Do not operate the fireplace with a damaged cord or plug, or after the heater malfunctions or has been dropped or damaged in any manner.
  • Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater.
  • This electric fireplace is intended for supplemental heat only and is NOT a main heat source.
  • Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
  • Always unplug the fireplace when not in use.

Package Contents

Verify that all components are present before installation:

  • PuraFlame Electric Fireplace Insert
  • Remote Control (2 AAA batteries included)
  • User Manual (this document)
  • Life-like Resin Log Set (pre-installed)

Setup and Installation

The PuraFlame Western Electric Fireplace Insert is designed for easy installation. With its flat bottom, the insert can simply sit directly on the floor within a suitable opening.

Dimensions and Fit

Before ordering or installing, please ensure your opening meets the required dimensions. The overall dimensions of the unit are 35 1/16" W x 26 31/32" H x 8 25/32" D. The firebox dimensions are 32 1/8" W x 25 9/16" H x 7 51/64" D.

Diagram showing the dimensions of the PuraFlame electric fireplace insert, including width, height, and depth measurements.

Figure 1: Product Dimensions Overview

Diagram illustrating the minimum and maximum width, height, and suggested depth for the fireplace opening to fit the insert.

Figure 2: Recommended Opening Dimensions for Installation

For optimal fit, the recommended opening dimensions are: Width: min 32.3" - max 34.3", Height: min 25.6" - max 26.6", Depth: suggest 8.1" (minimum 7.8").

Power Connection

Simply plug the unit into a standard 120V electrical outlet. Ensure the outlet is easily accessible. The unit is designed for plug-in use and cannot be hard-wired.

Front view of the PuraFlame electric fireplace insert with realistic flames and logs, and a remote control next to it.

Figure 3: PuraFlame Electric Fireplace Insert Ready for Use

Operating Instructions

Your PuraFlame electric fireplace can be operated using either the included remote control or the manual controls located on the unit.

Remote Control Functions

Diagram of the remote control for the PuraFlame fireplace, showing buttons for flame effects, 750W heater, 1500W heater, crackling sounds, and ON/OFF.

Figure 4: Remote Control Handset

  • ON/OFF Button: Powers the unit on or off.
  • FLAME Button: Cycles through 3 flame intensity settings. The flame effect can be used independently of the heat.
  • HEATER Buttons (750W / 1500W): Activates the fan heater at either 750 watts (low heat) or 1500 watts (high heat).
  • CRACKLING Button: Cycles through 6 crackling sound options, simulating a real wood-burning fire.

Manual Controls

Close-up view of the manual controls on the PuraFlame fireplace, showing the ON/OFF switch, flame setting button, heater settings (750W/1500W), and thermostat dial, with labels for air outlet and speaker.

Figure 5: Manual Control Panel

The manual controls are located behind a small access panel on the top right of the unit. These controls mirror the remote control functions, allowing you to adjust the ON/OFF, flame settings, heater output, and thermostat.

  • ON/OFF Switch: Main power switch.
  • Flame Button: Adjusts flame intensity (3 settings).
  • Heater Switch: Selects between 750W and 1500W heat output.
  • Thermostat Dial: Adjusts the desired room temperature. The heater will cycle on and off to maintain this setting.

The unit features a life-like resin log set, 11 13/16" high, sitting on a grate above an ember bed, mimicking a real wood-burning fireplace. The fuel bed has a depth of 7.5 inches.

Close-up of the fireplace's fuel bed with a measuring tape showing a depth of 7.5 inches.

Figure 6: Fuel Bed Depth Measurement

Maintenance

The PuraFlame electric fireplace is designed for minimal maintenance. Unlike traditional fireplaces, there is no need for cleaning dust or ashes.

  • Ensure the unit is unplugged and cool before cleaning.
  • Wipe the exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners or solvents.
  • Periodically check the air outlet for any obstructions and clear if necessary.

Troubleshooting

If you experience issues with your fireplace, please refer to the following common solutions:

ProblemPossible CauseSolution
No power/Unit does not turn onNot plugged in; Power outlet issue; Main power switch off.Ensure the unit is securely plugged into a working 120V outlet. Check the main ON/OFF switch on the unit.
No flame effectFlame effect is turned off.Press the FLAME button on the remote or manual control to activate or cycle through settings.
Heater not workingHeater not activated; Thermostat set too low; Overheat protection activated.Press the HEATER button on the remote or manual control. Adjust the thermostat to a higher setting. If the unit overheated, unplug it for 10-15 minutes to reset.
Remote control not workingDead batteries; Obstruction between remote and unit.Replace the AAA batteries in the remote. Ensure there is a clear line of sight to the unit's receiver.

If the problem persists, please contact PuraFlame customer service for assistance.

Specifications

FeatureDetail
BrandPuraFlame
Model NameEF45DFGF
Item Model NumberEF45D
Power SourceCorded Electric
Product Dimensions8.78"D x 35.04"W x 26.99"H
MaterialMetal, Resin, Tempered Glass
Finish TypeWood
Installation TypeFreestanding, Plug In, Wall Mount
Heat Output1500 Watts
Special FeatureAdjustable
StyleTraditional
ColorBlack
Room TypeBedroom, Home Office
Ventilation TypeVent Free
Heating Coverage400 square feet
Included ComponentsLog, Remote Control, User Manual
Specific Uses For ProductIndoor
Item Weight46.7 Pounds
OrientationFront-facing
Power Consumption1500 Watts
Chamber Depth8.78 Inches
Chamber Width8.78 Inches
Burner typeElectric
Batteries Required2 AAA (included)
Maximum Compatible Size33.19 Inches
Date First AvailableDecember 19, 2014

Warranty and Support

Your PuraFlame electric fireplace comes with a Limited Warranty. For specific warranty details, please refer to the documentation included with your purchase or contact PuraFlame customer service.

PuraFlame customer service is always ready to help whenever you need assistance with your product. You can visit the official PuraFlame store on Amazon for more information and support: PuraFlame Amazon Store.

© 2024 PuraFlame. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.