ChiliTec Outdoor Socket with Twilight Sensor and Timer - Model 21887 Instruction Manual

1. Introduction

This instruction manual provides essential information for the safe and proper use of your ChiliTec Outdoor Socket with Twilight Sensor and Timer, Model 21887. This device is designed to automatically control outdoor lighting and other electrical appliances based on ambient light conditions and a set timer. Please read this manual thoroughly before installation and operation, and retain it for future reference.

2. Safety Instructions

• Electrical Safety: Always ensure the power supply is disconnected before installation or maintenance. Only connect the device to a properly grounded 230V/50Hz power outlet.
• IP44 Rating: The robust plastic casing provides IP44 protection against splashing water. This means it is protected against water splashes from any direction. It is suitable for outdoor use but should be mounted in a suspended position and is not suitable for ground or submerged installation.
• Power Load: Do not exceed the maximum power load of 2300W (10A). Overloading can cause damage to the device and pose a fire hazard.
• Damage Inspection: Before each use, inspect the device and its cables for any signs of damage. Do not use a damaged device.
• Children and Pets: Keep the device out of reach of children and pets.
• Modifications: Do not attempt to modify or repair the device yourself. Contact qualified personnel for service.
• Sensor Placement: Ensure the twilight sensor is not obstructed and is not exposed to direct artificial light sources at night, as this can interfere with its operation.

3. Product Overview

The ChiliTec Outdoor Socket with Twilight Sensor and Timer is a compact, weather-resistant unit designed for easy integration into your outdoor electrical setup.

Figure 3.1: Overview of the ChiliTec Outdoor Socket with Twilight Sensor and Timer. This image shows the complete unit, featuring the input plug, the central control unit with a digital display, and the output socket with a protective cover.

Figure 3.2: Front view of the ChiliTec Outdoor Socket with its protective cover open. This view highlights the robust design and the accessible output socket, ready for connection to an appliance.

Components:

• Input Plug: Standard Type F (Schuko) plug for connecting to a power source.
• Control Unit: Central housing containing the twilight sensor, digital display, and selection button.
• Digital Display: Shows current mode or timer setting.
• Selection Button: Used to cycle through operating modes and timer settings.
• Output Socket: Type F (Schuko) socket for connecting your outdoor appliance, equipped with a protective cover.
• Cables: Integrated connection cables for input and output.

Figure 3.3: Detailed view of the ChiliTec Outdoor Socket with key components labeled. This image points out the 15cm connection cable with IP44 socket, the illuminated display, the IP44 rubberized selection switch, and the 15cm connection cable with IP44 plug, providing a clear understanding of each part's function and location.

4. Setup

The ChiliTec Outdoor Socket is designed for quick and easy setup. It comes pre-assembled and ready to plug in.

1. Placement: Choose a suitable outdoor location for the device. It should be mounted in a suspended position, away from direct ground contact, to ensure optimal performance and adherence to its IP44 rating. Ensure the twilight sensor is not obstructed by objects or structures.
2. Initial Connection: Plug the device's input plug into a grounded 230V/50Hz outdoor power outlet.
3. Calibration: Upon initial connection, the display will show 'F' and flash. Allow approximately one minute for the device to calibrate its twilight sensor. During this time, power will be supplied to the output socket.
4. Connect Appliance: Once calibrated, connect your outdoor appliance (e.g., garden lights, pond pump) to the device's output socket. Ensure the protective cover is securely closed over the socket when not in use or when an appliance is connected.

Figure 4.1: The ChiliTec Outdoor Socket mounted on a brick wall, demonstrating a typical suspended installation. This placement helps protect the device from ground moisture and ensures the sensor has an unobstructed view of ambient light.

5. Operating Instructions

The device offers several operating modes, controlled by a single selection button. The illuminated display indicates the current mode.

Operating Modes:

After the initial calibration (display shows 'F' and flashes), press the selection button to cycle through the following modes:

• 'F' (Flashing): Calibration mode. If you need to recalibrate the sensor, press and hold the button for 4 seconds until 'F' flashes again. This is useful if the ambient light conditions at the sensor's location have changed significantly.
• 'd': Dusk-to-Dawn mode. In this mode, the connected appliance will automatically turn on at dusk and turn off at dawn. The display will show a steady 'd' during the day and a flashing 'd' at night when the twilight sensor is active.
• '1' to '9': Timer mode. The appliance will turn on at dusk and remain on for the selected number of hours (1 to 9 hours). For example, '3' means it will turn off 3 hours after dusk.
• '0': Deactivation mode. The output socket is deactivated, and no power is supplied to the connected appliance.

To select a mode, simply press the button until the desired mode ('d', '1'-'9', or '0') appears on the display. The device will automatically save the selected setting.

Automatic Switching Delays:

• Turn-on Delay: Approximately 35 seconds. This delay prevents accidental switching due to brief changes in light conditions (e.g., car headlights).
• Turn-off Delay: Approximately 15 minutes. After the ambient brightness changes consistently (e.g., sunrise), the device waits for about 15 minutes before turning off. This prevents premature deactivation due to temporary shadows or passing clouds.

Figure 5.1: Example of the ChiliTec Outdoor Socket controlling various outdoor lighting. The image shows the device connected to a power source, with its output socket powering both a decorative garden light near a pond and string lights on a building, illustrating its versatility for different outdoor applications.

6. Maintenance

The ChiliTec Outdoor Socket is designed for durability and requires minimal maintenance.

• Cleaning: Disconnect the device from the power supply before cleaning. Wipe the exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents.
• Protective Cover: Always ensure the protective cover on the output socket is securely closed when not in use or when an appliance is connected, to maintain its IP44 weather resistance.
• Sensor Cleanliness: Keep the twilight sensor clean and free from dirt, dust, or obstructions to ensure accurate light detection.
• Storage: If storing the device for an extended period, disconnect it from the power supply and store it in a dry, protected environment.

7. Troubleshooting

If you encounter issues with your ChiliTec Outdoor Socket, refer to the following troubleshooting guide:

8. Specifications

9. Warranty and Support

For warranty information and technical support, please refer to the retailer or manufacturer's official website. Keep your proof of purchase for any warranty claims. Information regarding spare parts availability is not provided.