AUTOBOXCLUB EZ Pass Holder / Toll Pass Windshield Mount (Model SH043)

1. Introduction

This manual provides instructions for the installation and use of your AUTOBOXCLUB EZ Pass Holder, Model SH043. This product is designed to securely mount your electronic toll transponder to your vehicle's windshield, ensuring reliable operation and easy transfer between vehicles.

2. Package Contents

Verify that all items are present in your package:

• 1 x AUTOBOXCLUB Toll Pass Holder
• 4 x Reclosable Fasteners (Adhesive Strips)
• 2 x Suction Cups

3. Compatibility

The AUTOBOXCLUB EZ Pass Holder is designed to fit most major US toll passes, including both old and new models. This includes, but is not limited to, the following systems:

• EZ Pass (New York, New Jersey, Massachusetts, Maine, Vermont, Pennsylvania, Delaware, Illinois, Maryland, Ohio, South Carolina, Indiana, Virginia)
• FasTrak
• I-Pass
• I-Zoom
• Fast Lane with HOV switch
• Quick Pass
• Elite Pass
• PrePass

For specific compatibility with your local toll system, please refer to your state's highway authority guidelines.

Image: Map illustrating the wide compatibility of the toll pass holder across various US states and toll systems.

4. Setup and Installation

The AUTOBOXCLUB EZ Pass Holder offers two primary installation methods: using the included suction cups for easy removal and re-positioning, or using the adhesive strips for a more permanent attachment.

4.1. Suction Cup Installation (Recommended for frequent transfers)

1. Clean the Windshield: Ensure the chosen area on your windshield is clean and dry. Use a glass cleaner and a lint-free cloth to remove any dust, dirt, or residue.
2. Attach Suction Cups: Insert the stems of the two suction cups into the designated holes on the back of the toll pass holder. Ensure they are securely seated.
3. Insert Toll Pass: Slide your electronic toll transponder into the holder. The holder is designed to accommodate various transponder sizes.
4. Mount to Windshield: Press the suction cups firmly against the clean windshield surface in your desired location. Apply pressure to each suction cup until it creates a strong seal.
5. Verify Security: Gently tug on the holder to ensure it is securely attached and will not fall during vehicle operation.

Image: The AUTOBOXCLUB EZ Pass Holder featuring a US Flag design, shown with its integrated suction cups for windshield mounting.

Image: A person demonstrating the installation of the EZ Pass holder by pressing it onto the car's windshield.

4.2. Adhesive Strip Installation (Optional, for transponders without built-in adhesive)

If your toll transponder does not have its own adhesive strips, or if you prefer a more secure, semi-permanent attachment, you can use the included reclosable fasteners.

1. Prepare Transponder: Ensure the back of your toll transponder is clean and dry.
2. Apply Adhesive Strips to Transponder: Peel the backing from two of the reclosable fasteners and firmly press them onto the back of your toll transponder.
3. Apply Adhesive Strips to Holder: Peel the backing from the remaining two reclosable fasteners and firmly press them onto the designated areas on the inside of the toll pass holder.
4. Connect Transponder to Holder: Align the reclosable fasteners on the transponder with those on the holder and press them together until they securely interlock.
5. Mount to Windshield: Follow steps 4 and 5 from the "Suction Cup Installation" section to attach the holder (with the transponder inside) to your windshield.

Image: An exploded diagram illustrating the components of the EZ Pass holder, including the suction cups and adhesive tapes for mounting.

4.3. Optimal Mounting Locations

For best performance and visibility, consider the following mounting locations:

• Preferred: Near the rearview mirror, typically in the upper center portion of the windshield.
• Alternative: Other areas on the windshield that do not obstruct your view of the road.

Avoid placing the holder in areas that may interfere with vehicle sensors or driver visibility.

Image: A visual guide indicating recommended and alternative positions for mounting the toll pass holder on a car's windshield.

5. Operating Instructions

Once installed, the AUTOBOXCLUB EZ Pass Holder requires no special operation. Your toll transponder will function as usual. The holder's design ensures uninterrupted readability by toll booth sensors.

5.1. Transferring Between Vehicles

One of the key benefits of this holder is its ease of transfer:

1. Remove from Windshield: To remove the holder, gently pull on the release tabs of the suction cups (if using suction cups) or carefully pry the holder from the windshield (if using adhesive, this may require more effort).
2. Remove Toll Pass: Slide the toll transponder out of the holder.
3. Re-install: Follow the installation steps (Section 4) to mount the holder and transponder in another vehicle.

Image: A depiction of two different vehicles, highlighting the convenience of transferring the toll pass holder from one car to another.

6. Maintenance

6.1. Cleaning the Holder

To maintain optimal suction and appearance, clean the holder periodically:

• Wipe the holder with a soft, damp cloth.
• For stubborn dirt, use a mild soap solution. Avoid harsh chemicals or abrasive cleaners.

6.2. Cleaning Suction Cups

If suction cups lose their grip, they may need cleaning:

• Remove the suction cups from the holder.
• Rinse them with warm water and a small amount of dish soap.
• Allow them to air dry completely before reattaching.

7. Troubleshooting

7.1. Holder Not Sticking Securely

• Clean Surface: Ensure the windshield surface is thoroughly clean and dry before application. Any dust, dirt, or grease can prevent proper suction.
• Warm Suction Cups: In cold weather, warm the suction cups slightly (e.g., with warm water) before applying them to the windshield.
• Apply Firm Pressure: Press each suction cup firmly against the glass to expel all air and create a strong vacuum seal.
• Check for Damage: Inspect suction cups for any tears, cracks, or deformities that might compromise their ability to hold suction. Replace if damaged.

7.2. Toll Transponder Not Being Read

• Correct Orientation: Ensure the toll transponder is inserted into the holder in the correct orientation as specified by your toll authority.
• Clear Path: Verify that there are no obstructions (e.g., tint, other devices) between the transponder and the outside of the windshield.
• Holder Position: Confirm the holder is mounted in an approved location on your windshield, typically near the rearview mirror, to ensure optimal signal transmission.

8. Specifications

9. Warranty and Support

For warranty information or product support, please contact AUTOBOXCLUB customer service through their official website or the retailer where the product was purchased. Keep your proof of purchase for any warranty claims.