Introduction
The BRESSER Temeo Quadro Temperature Station is designed to monitor temperature and humidity at up to four different locations simultaneously. This system includes a main display unit and three remote sensors, allowing you to track environmental conditions both indoors and outdoors, or in various rooms of your home. The remote sensors transmit data wirelessly to the main unit via a 433 MHz radio signal.
Safety Information
- Read all instructions carefully before using the device.
- Keep this manual for future reference.
- Do not expose the device to extreme temperatures, direct sunlight, or high humidity.
- Avoid dropping or subjecting the device to strong impacts.
- Do not attempt to disassemble or repair the device yourself. Contact qualified service personnel.
- Dispose of used batteries responsibly according to local regulations.
Package Contents
- 1x BRESSER Temeo Quadro Main Display Unit
- 3x Remote Sensors
- 1x User Manual (this document)
Note: Batteries are not included. The main unit requires 3x AAA (LR03) batteries, and each remote sensor requires 2x AAA (LR03) batteries.
Product Overview
Main Display Unit
Image: Front view of the BRESSER Temeo Quadro main unit display. A clear view of the main unit's LCD screen, showing temperature and humidity values for four channels.
Image: Rear view of the BRESSER Temeo Quadro main unit, showing control buttons and battery compartment. The back of the main unit includes buttons for 'CHANNEL', 'ALARM', 'MAX/MIN', and 'SET', along with the battery compartment cover.
- LCD Display: Shows temperature and humidity for the main unit (IN) and up to three remote sensors (1, 2, 3).
- CHANNEL Button: Selects which remote sensor's data is displayed or cycles through channels.
- ALARM Button: Activates/deactivates temperature/humidity alarms.
- MAX/MIN Button: Displays maximum and minimum recorded values.
- SET Button: Enters setup mode for time, date, and alarm settings.
- Battery Compartment: Located on the rear, for 3x AAA batteries.
- Integrated Stand: For desktop placement.
Remote Sensor
Image: BRESSER Temeo Quadro remote sensor, front and back views. A remote sensor unit, showing its display on the front and the battery compartment and mounting hole on the back.
- LCD Display: Shows its current temperature and humidity.
- Channel Switch: Allows selection of channel 1, 2, or 3.
- Battery Compartment: For 2x AAA batteries.
- Mounting Hole: For wall mounting.
Setup
1. Battery Installation
- For Remote Sensors:
- Open the battery compartment cover on the back of each remote sensor.
- Insert 2x AAA (LR03) batteries into each sensor, observing the correct polarity (+/-).
- Set the channel switch (1, 2, or 3) on each sensor to a unique channel.
- Close the battery compartment cover.
- For Main Display Unit:
- Open the battery compartment cover on the back of the main unit.
- Insert 3x AAA (LR03) batteries, observing the correct polarity (+/-).
- Close the battery compartment cover. The main unit will power on and begin searching for sensor signals.
2. Sensor Pairing
- After installing batteries in both the sensors and the main unit, the main unit will automatically attempt to connect with the remote sensors.
- Ensure the remote sensors are within range (typically up to 30 meters in open air) of the main unit during initial setup.
- The corresponding channel numbers (1, 2, 3) on the main unit's display will show readings once a connection is established. The 'IN' channel displays the main unit's internal readings.
- If a sensor does not connect, remove and reinsert its batteries, then press the 'CHANNEL' button on the main unit to initiate a new search.
3. Placement
- Place the main unit indoors in a central location, away from direct sunlight or heat sources.
- Position remote sensors in desired monitoring areas. For outdoor use, place sensors in a sheltered spot to protect them from direct rain and sun, which can affect accuracy and device longevity.
Operating Instructions
Viewing Temperature and Humidity
- The main display unit continuously shows the current temperature and humidity for the internal sensor ('IN') and the three remote sensors (1, 2, 3).
- The display also indicates comfort levels (e.g., 'COM' for comfortable, 'DRY' for dry, 'WET' for wet) based on humidity levels.
MAX/MIN Records
- Press the MAX/MIN button once to display the maximum temperature and humidity recorded since the last reset.
- Press the MAX/MIN button a second time to display the minimum temperature and humidity recorded.
- To clear the MAX/MIN records, press and hold the MAX/MIN button for approximately 3 seconds while MAX or MIN values are displayed.
Temperature Unit Selection (°C/°F)
- On the main unit, press the SET button to toggle between Celsius (°C) and Fahrenheit (°F).
Setting Alarms (if applicable)
- Press the ALARM button to enter alarm setting mode.
- Use the CHANNEL and MAX/MIN buttons to adjust the desired high and low temperature/humidity alarm thresholds for each channel.
- Press ALARM again to confirm settings and activate the alarm. An alarm icon will appear on the display.
- When an alarm threshold is met, the unit will emit an audible alert and the corresponding channel's reading will flash.
Maintenance
- Cleaning: Wipe the device with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Battery Replacement: Replace batteries when the low battery indicator appears on the display. Always replace all batteries in a unit at the same time.
- Storage: If storing the device for an extended period, remove all batteries to prevent leakage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No display on main unit. | Batteries are dead or incorrectly inserted. | Check battery polarity and replace with fresh AAA batteries. |
| Remote sensor not displaying data on main unit. | Sensor out of range, incorrect channel setting, or dead batteries. |
|
| Inaccurate readings. | Sensor exposed to direct sunlight, heat sources, or moisture. | Relocate sensors to a more appropriate, sheltered environment. Allow time for readings to stabilize. |
| Intermittent signal loss. | Interference from other electronic devices or physical obstructions. | Move the main unit or sensors away from potential sources of interference (e.g., TVs, microwaves, large metal objects). |
Specifications
| Model Number | 7000020CM3000 |
| Brand | BRESSER |
| Product Dimensions (Main Unit) | 1.02 x 4.13 x 4.72 inches (2.59 x 10.49 x 11.99 cm) |
| Item Weight (Main Unit) | 0.19 Kilograms (approx. 6.7 ounces) |
| Temperature Range (Main Unit) | Internal sensor range not specified, but upper rating is 55 °C. |
| Temperature Accuracy | ±1 °C |
| Humidity Range | Not specified, but typically 20% to 95% for similar devices. |
| Wireless Frequency | 433 MHz |
| Power Source (Main Unit) | 3x AAA (LR03) batteries |
| Power Source (Remote Sensor) | 2x AAA (LR03) batteries per sensor |
| Number of Remote Sensors Supported | 3 |
Warranty
This BRESSER product comes with a two-year warranty against factory defects from the date of purchase. Please retain your proof of purchase for warranty claims. The warranty does not cover damage caused by improper use, accidents, unauthorized repairs, or normal wear and tear.
Support
For technical support, warranty claims, or further information, please visit the official BRESSER website or contact their customer service department. Refer to the packaging or the BRESSER website for the most current contact details.
Online resources may include FAQs, additional manuals, and contact forms.
