Sato PB-2 (PB-216) White Labels Instruction Manual

Introduction

These instructions provide guidance for the proper use and handling of Sato PB-2 (PB-216) White Labels. These labels are specifically designed for optimal performance with compatible Sato PB-216 series labelers. Adhering to these guidelines will ensure efficient operation and longevity of your labels.

Product Overview

The Sato PB-2 (PB-216) White Labels are high-quality, two-line labels intended for use in labelers that print two lines of information. Each sleeve contains 10 rolls, with 1,250 labels per roll, totaling 12,500 labels. These labels feature tamper-proof slits and a permanent adhesive for secure application.

An image showing a sleeve of Sato PB-2 (PB-216) White Labels, indicating the packaging for 12,500 labels.

Setup: Loading Labels

To load the Sato PB-2 (PB-216) White Labels into your compatible Sato PB-216 labeler, follow these general steps. Always refer to your specific labeler's manual for detailed instructions.

1. Open the Labeler: Locate and open the label compartment of your Sato PB-216 labeler. This usually involves pressing a release button or latch.
2. Remove Old Roll (if applicable): If an old roll of labels is present, carefully remove it and any remaining label backing.
3. Insert New Roll: Place a new roll of Sato PB-2 (PB-216) White Labels onto the spindle, ensuring the labels unwind from the top or as indicated by your labeler's design.
4. Feed Labels: Guide the leading edge of the label strip through the labeler's feed mechanism, past the print head, and out through the exit slot. Ensure the labels are properly aligned and seated.
5. Close the Labeler: Securely close the label compartment. Perform a few test prints to confirm proper feeding and alignment.

Operating: Using the Labels

Once the labels are loaded, proper operation ensures clear printing and effective adhesion.

• Print Head and Ink Roller: Ensure your labeler's print head is clean and the ink roller (if applicable) is properly installed and has sufficient ink. A clean print head is crucial for clear, legible prints.
• Adjust Print Settings: If your labeler allows, adjust the print settings to align with the two-line format of these labels. This ensures text is centered and fully printed on each label.
• Application Surface: For optimal adhesion, apply labels to clean, dry, and smooth surfaces. Rough, oily, or dusty surfaces may reduce the effectiveness of the permanent adhesive.
• Pressure Application: After dispensing a label, apply firm, even pressure across the entire label surface to activate the adhesive and ensure a secure bond.

Maintenance: Storage and Handling

Proper storage and handling are essential to maintain the quality and performance of your Sato labels.

• Storage Conditions: Store labels in their original packaging in a cool, dry place. Avoid direct sunlight, high humidity, and extreme temperatures, as these can degrade the adhesive and label material.
• Handling: Handle label rolls by the edges to avoid contaminating the adhesive surface with oils or dirt from your hands. Do not bend or crease the label rolls.
• Protect from Dust: Keep label rolls covered when not in use to prevent dust and debris from accumulating on the label surfaces.

Troubleshooting

If you encounter issues while using your Sato PB-2 (PB-216) White Labels, consider the following common solutions:

• Labels Not Feeding: Check that the label roll is correctly loaded and seated on the spindle. Ensure there are no obstructions in the label path within the labeler. Verify the labeler's feed mechanism is clean and free of debris.
• Poor Adhesion: Confirm that the surface to which the label is being applied is clean, dry, and free of dust, grease, or moisture. Ensure sufficient pressure is applied when adhering the label. Check the label's storage conditions to ensure the adhesive has not degraded.
• Faint or Incomplete Print: This issue is typically related to the labeler itself. Inspect the labeler's ink roller for sufficient ink and proper installation. Clean the print head according to your labeler's maintenance instructions.
• Labels Jamming: Ensure the labels are not creased or damaged before loading. Verify the label roll is not too tight or too loose on the spindle. Check for any foreign objects inside the labeler.

Specifications

Warranty and Support

This manual provides instructions for the Sato PB-2 (PB-216) White Labels. For warranty information regarding Sato products, including the labels or your Sato PB-216 labeler, please refer to the documentation provided with your specific labeler or contact Sato customer service directly. Support contact details can typically be found on the manufacturer's official website or within your labeler's user manual.