1. Introduction
The Anex Magdora 22 No. 59-5B is a compact multi-bit stubby screwdriver set designed for precision work in confined spaces. Its ultra-short bit attachment and ergonomic handle make it ideal for tasks where standard screwdrivers are too long. This manual provides essential information for the safe and effective use, maintenance, and troubleshooting of your Anex Magdora 22 Stubby Driver Set.
2. Safety Information
Always observe the following safety precautions when using hand tools:
- Wear appropriate personal protective equipment, such as safety glasses, to protect against flying debris.
- Ensure the correct bit size and type are used for the fastener to prevent damage to the fastener or the tool.
- Do not use the tool if it is damaged. Inspect the handle and bits before each use.
- Do not apply excessive force that could cause the tool to slip or break.
- Keep hands and fingers clear of the working area.
- Store the tool and bits in a dry, secure place, out of reach of children.
3. Package Contents
The Anex Magdora 22 No. 59-5B Stubby Driver Set includes the following components:
- 1 x Handle Body
- 1 x Bicho Holder
- 5 x Ultra-short bits (including +1, +2 (2 pieces), +3, and -6)
Note: The total quantity of items in the set is 12 pieces, which includes the handle, holder, and bits.
This image displays the Anex Magdora 22 No. 59-5B Stubby Driver Set in its retail packaging. It highlights the compact handle, the included ultra-short bits (Phillips and Slotted), and the magnetic bit holder. The packaging also illustrates the tool's suitability for narrow spaces with dimensions of 22mm head width and 30mm bit length.
4. Setup
- Select the Correct Bit: Identify the appropriate bit type and size (+1, +2, +3, or -6) for your fastener.
- Insert the Bit: Firmly insert the selected bit into the Bicho holder. The magnetic holder will secure the bit in place.
- Attach to Handle: Insert the Bicho holder with the bit into the handle body. Ensure it is fully seated.
The compatible bit size for this tool is a single head bit with a 0.25 inch (6.35 mm) hex shaft and a total length of 0.75 inch (19 mm) or above.
5. Operating Instructions
- Position the Tool: Place the tip of the bit into the head of the fastener.
- Apply Pressure: Apply firm, steady downward pressure on the handle to keep the bit engaged with the fastener.
- Turn the Handle: Rotate the handle clockwise to tighten or counter-clockwise to loosen the fastener. The 4-groove handle design provides an easy grip for applying force.
- Working in Narrow Spaces: The ultra-short bit attachment and 22mm head width are specifically designed for accessing fasteners in tight or restricted areas.
- Magnetic Bit Retention: The magnetic feature of the Bicho holder helps prevent bits from falling out during use, especially when working overhead or in awkward positions.
6. Maintenance
- Cleaning: Wipe the handle and bits with a clean, dry cloth after each use to remove dirt, grease, or debris. Do not use harsh chemicals or abrasive cleaners.
- Inspection: Regularly inspect bits for wear, damage, or corrosion. Replace worn or damaged bits immediately to ensure optimal performance and safety.
- Storage: Store the stubby driver set and its bits in a dry environment to prevent rust and corrosion. Keep them organized to easily find the correct bit for future tasks.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Bit slips out of fastener head | Incorrect bit size/type; insufficient downward pressure; worn fastener head or bit. | Ensure correct bit is used. Apply more downward pressure. Replace worn bit or fastener. |
| Bit does not stay in holder | Bit not fully inserted; magnetic holder weakened; incompatible bit. | Push bit firmly into holder. Ensure bit is 0.25 inch hex. If magnetic holder is faulty, contact support. |
| Difficulty turning fastener | Fastener is seized or overtightened; incorrect bit size. | Apply penetrating oil if seized. Ensure correct bit size. Do not force, as this may damage the fastener or tool. |
8. Specifications
- Brand: Anex
- Model Number: No.59-5B
- Part Number: No.59-5B
- Item Weight: 1.03 pounds
- Package Dimensions: 7.17 x 5.98 x 2.99 inches
- Style: 12pcs
- Number Of Pieces: 12
- Compatible Fastener Range: 0.25 inches (6.35mm hex shaft)
- Usage: Stubby
- Batteries Required?: No
9. Warranty and Support
For warranty information or technical support, please refer to the manufacturer's official website or contact your retailer. Keep your purchase receipt as proof of purchase.
Manufacturer: Anex Tools
Website: www.anextool.co.jp/en/ (Example link, please verify official website)
