Acova Evolution Regulation Control Box User Manual

Introduction

This manual provides essential information for the safe and efficient use of your Acova Evolution Regulation Control Box. This control box is designed to regulate Acova radiators, specifically compatible with models Taq-100-076-02, Taq-125-084-2 taiga, and Taq-200-123-2 taiga.

Please read this manual thoroughly before installation and operation, and retain it for future reference.

Important Safety Information

• Professional Installation Recommended: Due to the electrical nature of this product, installation by a qualified professional is strongly recommended to ensure safety and proper functionality.
• Power Disconnection: Always disconnect power to the radiator and the control box before performing any installation, maintenance, or troubleshooting.
• Environmental Conditions: Do not expose the control box to excessive moisture, direct water spray, or extreme temperatures.
• Authorized Parts: Use only genuine Acova replacement parts.

Product Overview

The Acova Evolution Regulation Control Box (Model 3566550041452) is a white (RAL9016) module designed to integrate with and control specific Acova radiator models.

Image 1: Acova Evolution Regulation Control Box. This image displays the white control box with its internal components and wiring visible. A transparent cover protects a rotary dial on the left side of the unit.

Setup and Installation

Note: Installation should ideally be performed by a certified electrician or heating professional.

1. Power Off: Ensure the main power supply to the radiator system is completely disconnected at the circuit breaker.
2. Access Radiator Control Area: Refer to your specific Acova radiator manual for instructions on accessing the control module bay.
3. Connect Wiring: Carefully connect the wires from the radiator to the corresponding terminals on the Acova Evolution Regulation Control Box. Ensure all connections are secure and follow the wiring diagram provided with your radiator or by a professional.
4. Secure the Control Box: Mount the control box securely within the designated area of the radiator.
5. Restore Power: Once installation is complete and all connections are verified, restore power to the system.
6. Initial Test: Perform an initial test to ensure the control box powers on and communicates with the radiator as expected.

Operating Instructions

The Acova Evolution Regulation Control Box provides temperature regulation for your compatible Acova radiator. While specific functions may vary slightly depending on the radiator model, the general operation involves setting the desired temperature.

• Temperature Adjustment: Use the rotary dial (visible under the transparent cover) to set the desired room temperature. Turning the dial clockwise typically increases the temperature, while turning it counter-clockwise decreases it.
• Indicator Lights: Observe any indicator lights on the control box or radiator for operational status (e.g., heating active, standby). Refer to your radiator's manual for specific light indications.
• Programming (if applicable): Some Acova radiator systems allow for programming schedules. If your radiator supports this, the control box will execute these programmed settings. Consult your radiator's manual for programming details.

Maintenance

The Acova Evolution Regulation Control Box requires minimal maintenance.

• Cleaning: Periodically wipe the exterior of the control box with a soft, dry cloth. Do not use abrasive cleaners, solvents, or excessive moisture.
• Inspection: Annually, or if you suspect an issue, have a qualified professional inspect the wiring connections and the overall condition of the control box.
• No User-Serviceable Parts: There are no user-serviceable parts inside the control box. Do not attempt to open or repair the unit yourself.

Troubleshooting

If you experience issues with your Acova Evolution Regulation Control Box, consider the following common troubleshooting steps:

• No Power:
  • Check the main power supply to the radiator system at the circuit breaker.
  • Ensure all wiring connections to the control box are secure.
• Radiator Not Heating:
  • Verify the temperature setting on the control box is higher than the current room temperature.
  • Check if the radiator itself is receiving power and is operational (refer to radiator manual).
  • Ensure the control box is correctly installed and communicating with the radiator.
• Inaccurate Temperature:
  • Ensure the control box is not obstructed or exposed to direct heat sources that could affect its temperature sensor.
  • If the issue persists, professional calibration or inspection may be required.
• Unusual Noises or Smells:
  • Immediately disconnect power to the unit and contact a qualified professional.

For persistent issues, contact Acova customer support or a certified technician.

Specifications

Warranty and Support

Information regarding the warranty for the Acova Evolution Regulation Control Box is not available in the provided product details. Please refer to your purchase documentation or contact Acova customer service directly for warranty terms and support.

For technical assistance or service, it is recommended to contact a qualified heating professional or Acova authorized service center.