1. Introduction
Thank you for choosing the AMIR Upgraded Motion Sensor Light. This manual provides essential information for the safe and efficient use of your new motion-activated LED lights. Please read these instructions carefully before installation and operation, and retain them for future reference.
Image 1: Overview of three AMIR Upgraded Motion Sensor Lights.
2. Product Features
- Automatic Sensor: Activates within 10 feet (3 meters) and automatically turns off after 12-17 seconds of no motion detected.
- Light Sensor: Operates only in dark conditions; will not activate if sufficient ambient light is detected.
- Battery Operated: Requires 4 AAA batteries (not included) for wireless operation.
- Ideal Illumination: Each light features 10 LEDs, providing adequate light for various indoor spaces.
- Simple Installation: Utilizes an adhesive strip with magnetic fields for easy attachment and detachment. No tools, screws, or nuts are required.
Image 2: Key features including automatic motion sensing, auto-off timer, and product dimensions (7.4 inches long, 1.2 inches wide).
3. Setup and Installation
- Insert Batteries: Open the battery compartment and insert 4 AAA batteries (not included), ensuring correct polarity.
- Prepare Surface: Clean and dry the desired installation surface. Ensure it is smooth and free of dust or grease.
- Attach Magnetic Strip: Peel off the protective film from one side of the adhesive magnetic strip. Attach this side firmly to the desired installation surface.
- Mount Light: The light unit has built-in magnets. Simply attach the light unit to the magnetic strip on the wall. This allows for easy removal for battery replacement or relocation.
Image 3: Illustration of the battery compartment and the magnetic strip with double-sided tape for installation.
Important Installation Considerations:
- Do not install in high-temperature areas, as this can affect the adhesive strip's effectiveness.
- Avoid installing two lights too close together, as this may interfere with their motion detection.
- Do not install near heat sources (e.g., ovens, radiators).
- Do not face the lights towards air vents, as air currents can trigger the motion sensor.
- Do not mount in moist places (e.g., directly inside a shower), as the product is not water-resistant.
Image 4: Visual guide illustrating situations where the light may not function correctly due to improper placement.
4. Operating Instructions
The AMIR Motion Sensor Light is designed for automatic, hands-free operation:
- The light will automatically turn on when motion is detected within approximately 10 feet (3 meters) in a dark environment.
- The integrated light sensor prevents activation during daylight or in well-lit areas, conserving battery life.
- After motion ceases, the light will remain on for 12-17 seconds before automatically turning off.
Image 5: Examples of the motion sensor lights installed in a closet, drawer, under a bed, and under kitchen cabinets.
5. Maintenance
- Battery Replacement: When the light output dims or the unit stops functioning, replace all 4 AAA batteries with new ones. Ensure correct polarity.
- Cleaning: Wipe the light's surface with a soft, dry cloth. Do not use abrasive cleaners or immerse the unit in water.
- Storage: If storing the lights for an extended period, remove the batteries to prevent leakage.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | 1. Batteries are dead or incorrectly installed. 2. Ambient light is too bright. 3. No motion detected. | 1. Replace batteries, ensuring correct polarity. 2. Move to a darker location. 3. Ensure motion occurs within the sensor's range (10 feet). |
| Light falls off the surface. | 1. Adhesive strip not properly applied. 2. Surface is dirty, uneven, or too hot. | 1. Reapply the adhesive strip to a clean, dry surface. 2. Ensure installation on a smooth, clean surface. Avoid high-temperature areas. |
| Light turns on unexpectedly. | 1. Air currents from vents. 2. Another light source interfering. | 1. Relocate the light away from air vents. 2. Ensure no other light sources are directly affecting the sensor. |
7. Specifications
- Brand: AMIR
- Model Name: Upgraded Motion Sensor Light
- Model Number: US-UF10_2PCS
- Power Source: Battery Powered (4 x AAA batteries, not included)
- Light Source Type: LED (10 LEDs per light)
- Light Color: Pure White
- Special Feature: Motion Sensor
- Installation Type: Adhesive, Two-sided tape (Magnetic attachment)
- Indoor/Outdoor Usage: Indoor only
- Voltage: 6 Volts
- Material: Acrylonitrile Butadiene Styrene, Aluminum
- Item Weight: Approximately 4 Ounces (per unit)
- Product Dimensions (approximate): 7.4 inches (L) x 1.2 inches (W)
- Water Resistance Level: Not Water Resistant
- Number of Items: 3 (in a pack)
Image 6: Lighting Facts label, indicating 70 lumens brightness and estimated energy cost.
8. Warranty and Support
Specific warranty details and direct support contact information are not provided in this manual. For warranty inquiries or technical assistance, please refer to the product packaging or contact the retailer where the product was purchased. You may also visit the official AMIR brand store for general information.
AMIR Brand Store: Visit the AMIR Store on Amazon
