Introduction
This manual provides essential instructions for the safe assembly, operation, and maintenance of your Acme Furniture Xander Twin Red Go Kart Bed. Please read all instructions carefully before beginning assembly and retain this manual for future reference.
Safety Information
WARNING: Failure to follow these safety instructions could result in serious injury.
- Always assemble the bed according to the instructions provided. Ensure all bolts and fasteners are securely tightened before use.
- Do not allow children to jump on the bed. This bed is designed for sleeping and resting.
- The maximum weight recommendation for this bed is 250 pounds. Do not exceed this limit.
- Regularly check all connections and hardware to ensure they remain tight. Loose parts can lead to instability and injury.
- Keep small parts away from children during assembly to prevent choking hazards.
- Ensure the bed is placed on a level surface to prevent tipping.
Package Contents
Before assembly, verify that all components listed below are present. If any parts are missing or damaged, do not proceed with assembly. Contact customer support for assistance.
- Headboard with Racing Flag Decor
- Footboard
- Side Rails (Left and Right)
- Slat System
- Go Kart Frame Components (Roll Bar, Wheel Frames)
- Wheels (Decorative)
- Hardware Pack (bolts, washers, nuts, Allen wrench)
- Assembly Instructions
Setup and Assembly
Assembly typically requires two adults. Please follow the numbered steps in the included assembly diagram. All pieces are labeled for easier identification.
- Unpack and Identify Parts: Carefully remove all components from the packaging. Lay them out on a soft, clean surface to prevent scratches. Identify each part using the provided labels and the parts list.
- Attach Side Rails to Headboard and Footboard: Connect the side rails to the headboard and footboard using the designated bolts and washers. Do not fully tighten bolts until all major components are connected.
- Assemble Go Kart Frame: Attach the roll bar and wheel frame components to the main bed frame as indicated in the diagram. Ensure all connections are secure.
- Install Slat System: Place the slat system onto the side rails. Secure the slats to the side rails using the provided fasteners. The slat system eliminates the need for a box spring.
- Attach Decorative Wheels: Secure the decorative wheels to the wheel frames.
- Final Tightening: Once all components are in place and aligned, fully tighten all bolts and fasteners. Do not overtighten.
- Placement: Position the assembled bed in its desired location. Ensure there is adequate space around the bed for safety.
Operating Instructions
This bed is designed to accommodate a standard twin-size mattress. A mattress is not included with this product.
- Mattress Placement: Carefully place a twin-size mattress onto the slat system. Ensure the mattress fits snugly within the frame.
- Weight Capacity: The bed is designed to support a maximum weight of 250 pounds, including the mattress and occupant.
- Intended Use: This bed is intended for sleeping and resting. Avoid excessive force or activities that could compromise the structural integrity of the bed.
Maintenance and Care
Proper care will extend the life and appearance of your bed.
- Cleaning: Wipe the metal frame with a soft, damp cloth. Avoid using harsh chemicals, abrasive cleaners, or polishes that could damage the finish.
- Hardware Check: Periodically inspect all bolts and fasteners to ensure they are tight. Re-tighten as necessary to maintain stability.
- Avoid Moisture: Keep the bed in a dry environment. Prolonged exposure to moisture can lead to rust or damage to the metal.
- Moving the Bed: When moving the bed, lift it rather than dragging it to prevent damage to the frame and flooring.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Bed feels wobbly or unstable | Loose hardware connections. | Check and tighten all bolts and fasteners. Ensure the bed is on a level surface. |
| Squeaking noises | Loose connections or friction between metal parts. | Tighten all hardware. Apply a small amount of lubricant (e.g., silicone spray) to connection points if necessary. |
| Parts do not align during assembly | Incorrect orientation of parts or bolts not fully loosened. | Review the assembly diagram to ensure parts are oriented correctly. Loosen all bolts slightly, align parts, then re-tighten. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | AC-37645T |
| Brand | Acme Furniture |
| Style | Twin Bed (Go Kart Design) |
| Color | Red |
| Frame Material | Metal |
| Overall Dimensions (L x W x H) | 84" x 56" x 51" |
| Item Weight | 62 pounds |
| Maximum Weight Recommendation | 250 pounds |
| Box Spring Required | No (Slat System Included) |
| UPC | 840412030888 |
Warranty and Support
Acme Furniture products are manufactured with quality and care. For specific warranty details, please refer to the warranty card included with your purchase or visit the official Acme Furniture website. If you have any questions, require replacement parts, or need assistance with assembly, please contact Acme Furniture customer support.
Customer Support:
- Website: Visit the Acme Store on Amazon
- Contact Information: Refer to your purchase documentation for direct contact details.