Dogtra 202C No-Nonsense Dog Training Collar User Manual

1. Introduction

The Dogtra 202C No-Nonsense Dog Training Collar is a compact and intuitive training system designed for two dogs weighing 10 lbs and up. It provides low to medium power stimulation, offering effective training solutions for various canine behaviors. This manual will guide you through the proper setup, operation, and maintenance of your Dogtra 202C system.

Figure 1: Dogtra 202C Training Collar System

2. Key Features

• Low to medium power stimulation for sensitive dogs or mild temperaments.
• 1/2-mile range, suitable for various training environments.
• Ultra-compact receiver, designed for dogs as small as 10 lbs.
• 100-level Rheostat Dial for gradual and precise stimulation control.
• Nick (momentary stimulation) and Constant (continuous stimulation) modes.
• High Performance Pager (HPP) vibration for non-stimulation alerts.
• Fully waterproof receiver and transmitter.
• Rechargeable Lithium Polymer batteries (included).

Figure 2: Dogtra 202C Key Features

Figure 3: 202C Operating Range

3. Package Contents

Your Dogtra 202C system includes the following components:

• Dogtra 202C Transmitter (Remote)
• Two Dogtra 202C Receivers (Collars)
• Battery Charger and Splitter Cable
• Owner's Manual
• Test Light
• Lanyard

4. Setup Guide

4.1 Charging the Batteries

Before using the Dogtra 202C for the first time, fully charge the batteries for both the transmitter and receivers. The system comes with a splitter cable allowing simultaneous charging of both receivers and the transmitter.

1. Connect the charger to a standard wall outlet.
2. Attach the splitter cable to the charging ports on the transmitter and both receivers.
3. Charge for approximately 2 hours, or until the LED indicator on the units turns solid green.

4.2 Fitting the Receiver Collar

Proper fit of the receiver collar is crucial for consistent and effective stimulation. The contact points must have direct contact with the dog's skin.

1. Position the receiver on the dog's neck, directly below the ears, on the underside.
2. Ensure the contact points are touching the skin. You may need to trim some of the dog's fur if it is very thick.
3. The collar should be snug enough that you can only fit two fingers comfortably between the strap and your dog's neck.
4. Allow the dog to wear the collar for several minutes to ensure comfort before training.

Figure 4: Dog wearing the 202C Receiver Collar

5. Operating Instructions

5.1 Transmitter Controls

Figure 5: 202C Transmitter Key Features

• Rheostat Dial: Located on top of the transmitter, this dial allows you to adjust the stimulation level from 0 (lowest) to 100 (highest). Turn the dial clockwise to increase stimulation and counter-clockwise to decrease it.
• Nick Button (Black/Orange): Press and release this button for a single, quick pulse of stimulation. Use the black button for the black-collared dog and the orange button for the orange-collared dog.
• Constant Button (Black/Orange): Press and hold this button for continuous stimulation for up to 12 seconds. The stimulation will automatically shut off after 12 seconds as a safety feature. Use the black button for the black-collared dog and the orange button for the orange-collared dog.
• Pager Button (Black/Orange): Press this button for a non-stimulating vibration. This can be used as a warning or a command. Use the black button for the black-collared dog and the orange button for the orange-collared dog.

5.2 Turning On/Off the System

The Dogtra 202C system does not have traditional on/off switches. The transmitter is always in standby mode. To activate the receivers (collars), touch the red dots on the receiver and transmitter together for a moment. The receiver will turn on. To turn off, repeat the process.

5.3 Using the Test Light

The included test light can be used to verify that the receiver is functioning correctly and to check the stimulation level.

1. Place the test light over the receiver's contact points.
2. Press the Nick or Constant button on the transmitter. The test light should flash, indicating stimulation is being emitted. A brighter flash indicates a higher stimulation level.
3. Press the Pager button. The test light will not flash, but you should feel the vibration.

6. Care and Maintenance

• Regularly inspect the receiver collar for any signs of wear or damage.
• Clean the contact points and the receiver casing with a damp cloth. Avoid using harsh chemicals.
• Ensure the charging port cover is securely closed when not charging to maintain waterproofing.
• Store the system in a cool, dry place when not in use.
• Charge the batteries fully at least once every 3-4 months to prolong battery life, even if not in regular use.

7. Troubleshooting

For further assistance, please refer to the support section or contact Dogtra customer service.

8. Technical Specifications

9. Warranty and Support

The Dogtra 202C comes with a 1-year manufacturer's warranty. Please retain your proof of purchase for warranty claims.

For technical support, troubleshooting assistance, or warranty inquiries, please visit the official Dogtra website or contact their customer service department.

You can find more information and contact details at the Dogtra Store on Amazon.

10. Important Safety Information

Proposition 65 Warning: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

Always use the training collar responsibly and in accordance with local laws and regulations. Consult with a professional dog trainer if you are unsure about proper training techniques.

11. Video Resources (If Available)

No official product videos from the seller were available in the provided data to embed directly into this manual. Please check the product's Amazon page or the manufacturer's website for any available video tutorials or demonstrations.