Introduction
The Mr Beams MB720A is a wireless, battery-powered motion-sensing nightlight designed to provide soft, sleep-friendly amber LED illumination. This manual provides instructions for the proper setup, operation, and maintenance of your nightlight to ensure optimal performance.
Product Features
- Designed for sleep areas such as bedrooms, bathrooms, and hallways.
- Amber light provides soft safety lighting for nighttime and morning use.
- Sleep-friendly amber LED emits 20 lumens of light at 600nm, which does not disrupt sleep.
- Provides approximately one year of light on each set of batteries (not included) with average use (8-10 activations per night).
- Integrated motion and light sensors activate the light only when motion is detected in dark conditions.
- Automatic shut-off after 30 seconds of no motion helps conserve battery life.
- Battery-powered for wireless installation in under 5 minutes using included screws or double-sided adhesive.
Figure 1: Key features of the MB720A nightlight.
Package Contents
The MB720A nightlight package includes the following items:
- Mr Beams MB720A Nightlight Unit
- Mounting Hardware & Anchors
- Adhesive Strip
- User Manual (this document)
Setup
1. Battery Installation
- Remove the back cover of the nightlight. This typically involves sliding the cover down and then pulling it off.
- Insert four (4) AA batteries (not included) into the battery compartment. Ensure the flat (negative) end of each battery aligns with the spring in the unit.
- Replace the back cover, ensuring it clicks securely into place.
2. Mounting
The MB720A can be mounted using either the included screws and anchors or the double-sided adhesive strip.
- Screw Mounting: Use the provided screws and anchors to securely attach the nightlight to a wall or other surface.
- Adhesive Mounting: Apply the double-sided adhesive strip to the back of the nightlight and press firmly onto a clean, dry surface.
Consider placement in sleep areas such as bedrooms, bathrooms, or hallways where soft, motion-activated light is desired.
Figure 2: Nightlight placement in a bedroom.
Figure 3: Nightlights providing path illumination in a hallway.
Operating Instructions
The MB720A nightlight operates automatically using its integrated motion and light sensors.
- Automatic Activation: The nightlight will only activate when motion is detected in dark conditions. It will not turn on if there is sufficient ambient light.
- Motion Detection: The motion sensor has a detection angle of 120 degrees and a range of up to 15 feet (4.5 meters).
- Automatic Shut-off: The light will automatically turn off approximately 30 seconds after the last detected motion.
Figure 4: Nightlight in use in a bathroom.
Maintenance
Battery Replacement
The nightlight is designed for approximately one year of battery life with typical usage. When the light output diminishes or the unit stops activating, it is time to replace the batteries.
- Remove the back cover.
- Remove the old batteries and dispose of them according to local regulations.
- Insert four new AA batteries, ensuring they are from the same new pack for consistent performance. Energizer or Rayovac batteries are recommended.
- Replace the back cover.
Cleaning
Wipe the nightlight with a soft, damp cloth as needed. Do not use abrasive cleaners or immerse the unit in water.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on in the dark. | 1. Insufficient darkness. 2. Dead or improperly installed batteries. 3. Sensor reset required. | 1. Ensure the area is sufficiently dark for the photocell sensor to activate. 2. Check battery orientation and replace with fresh batteries if necessary. 3. Perform a sensor reset: Place the light in a well-lit room with the sensor facing the light for 10 minutes, then move it to a dark, motionless room for 10 full minutes. Test in a dark room. |
| Light turns on randomly or stays on. | 1. Constant motion in detection range. 2. Sensor interference or fault. 3. Sensor reset required. | 1. Ensure there are no objects or environmental factors (e.g., drafts, pets) causing constant motion within the sensor's range. 2. Perform a sensor reset as described above. If the issue persists, contact customer support. |
| Light is dim. | Low battery power. | Replace all batteries with a fresh set. |
Specifications
| Feature | Detail |
|---|---|
| Model | MB720A |
| Luminous Flux | 20 Lumens |
| Light Color Temperature | 600nm (Amber) |
| Lighting Modes | Motion Activated |
| Motion Angle of Detection | 120° |
| Motion Range | Up to 15 ft. (4.5 meters) |
| Auto Shut Off | 30 Seconds |
| Power | 4 x AA Batteries (not included) |
| Operating Conditions | 0 - 131°F (-17.8 - 55°C) |
| Mounting | Wall or Stand |
| Weatherproof Rating | IPX4 |
| Available Colors | White |
| Unit Dimensions | 3.86 x 3.39 x 1.14 Inches (9.8 x 8.6 x 2.9 cm) |
| Unit Weight | 0.31 Pounds (0.14 kg) |
Figure 5: Product dimensions.
Warranty
All Mr Beams products are guaranteed against defects in workmanship and materials for 1 year from the date of purchase. Use of Mr Beams lights is subject to the terms found on the official product support page.
Support
For additional information or assistance, please visit the Mr Beams product support page.
