Smartwares SC45

Download PDF
Contents

Smartwares SC45 Motion Sensor Alarm System User Manual

Model: SC45 (10.023.35)

1. Introduction

Thank you for choosing the Smartwares SC45 Motion Sensor Alarm System. This device is designed to secure small areas such as kiosks, apartments, or small shops by detecting motion and triggering a loud alarm. Please read this manual carefully before installation and use to ensure proper operation and safety.

2. Safety Information

  • Keep the device away from water and moisture.
  • Do not attempt to open or repair the device yourself. Refer to qualified personnel for service.
  • Ensure batteries are inserted with correct polarity.
  • Replace all batteries at the same time. Do not mix old and new batteries.
  • Dispose of batteries responsibly according to local regulations.
  • This device is intended for indoor use only.

3. Package Contents

The package should contain the following items:

  • 1x Smartwares SC45 Motion Sensor Alarm Unit
  • 2x Remote Controls
  • 4x AA Batteries (for the sensor unit)
  • Mounting hardware (screws and wall plugs, or adhesive strips)

4. Product Overview

Familiarize yourself with the components of your Smartwares SC45 Motion Sensor Alarm System.

Smartwares SC45 Motion Sensor Alarm unit and one remote control

Figure 1: The Smartwares SC45 Motion Sensor Alarm unit with one remote control. The sensor unit is white with a dark grey detection lens and a red indicator light at the bottom. The remote control is also white with 'ON' and 'OFF' buttons.

Side view of Smartwares SC45 Motion Sensor Alarm with mounting bracket

Figure 2: Side view of the motion sensor alarm unit, showing the integrated mounting bracket for wall or corner installation.

Close-up of Smartwares SC45 remote control

Figure 3: Close-up view of the remote control, featuring distinct 'ON' and 'OFF' buttons and a red indicator light.

5. Setup and Installation

5.1 Battery Installation

  1. Locate the battery compartment on the back of the motion sensor unit.
  2. Slide open the battery cover.
  3. Insert the 4 AA batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
  4. Close the battery cover securely.
  5. The unit will emit a short beep to indicate it is powered on.

5.2 Mounting the Sensor

The Smartwares SC45 can be mounted using adhesive strips or screws. Choose a location that provides optimal coverage of the area you wish to protect, typically in a corner or on a wall, facing the entry point.

  • For Adhesive Mounting: Clean the desired surface thoroughly. Apply strong double-sided adhesive strips (not included, unless specified in package contents) to the back of the sensor unit and press firmly onto the wall.
  • For Screw Mounting:
    1. Mark the desired mounting position on the wall.
    2. Drill pilot holes if necessary.
    3. Secure the mounting bracket (if detachable) or the unit directly using the provided screws.
    4. Ensure the sensor is positioned to cover the intended detection area. The detection range is up to 8 meters.
Smartwares SC45 Motion Sensor Alarm installed in a room corner

Figure 4: Example of the motion sensor alarm installed in the corner of a room, providing wide coverage.

6. Operating Instructions

The Smartwares SC45 is operated using the included remote controls.

6.1 Arming the Alarm

  • Press the ON button on the remote control.
  • The sensor unit will emit a short beep, and the red indicator light will flash briefly, indicating that the alarm is armed.
  • There is an exit delay period (typically 10-15 seconds) during which you can leave the protected area without triggering the alarm.

6.2 Disarming the Alarm

  • Upon entering the protected area, the sensor will detect motion and an entry delay period will begin (typically 5-10 seconds).
  • During this delay, press the OFF button on the remote control.
  • The sensor unit will emit a short beep, and the red indicator light will turn off, indicating that the alarm is disarmed.
  • If the alarm is not disarmed within the entry delay period, the siren will sound.

6.3 Alarm Trigger

  • If motion is detected while the alarm is armed and the entry delay expires without disarming, the siren will sound at 105 dB.
  • The alarm will typically sound for a set duration (e.g., 30-60 seconds) and then reset, re-arming itself.

7. Maintenance

7.1 Battery Replacement

When the alarm unit's indicator light remains dimly lit or the alarm performance degrades, it is time to replace the batteries.

  1. Disarm the alarm.
  2. Open the battery compartment on the back of the unit.
  3. Remove the old AA batteries.
  4. Insert 4 new AA alkaline batteries, observing correct polarity.
  5. Close the battery cover.
  6. Test the alarm's functionality with the remote control.

Note: Remote control batteries (e.g., CR2032 coin cell) may also need occasional replacement. Refer to the remote control's specific instructions if provided.

7.2 Cleaning

Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the unit.

8. Troubleshooting

ProblemPossible CauseSolution
Alarm does not arm/disarm with remote.
  • Dead remote battery.
  • Sensor batteries are low or dead.
  • Remote out of range.
  • Replace remote battery.
  • Replace sensor batteries.
  • Move closer to the sensor unit.
Alarm triggers unexpectedly.
  • Pet or object moving in detection zone.
  • Sensor positioned near heat source or draft.
  • Faulty sensor.
  • Adjust sensor angle or relocate.
  • Reposition sensor away from heat/drafts.
  • Contact customer support.
Alarm siren is weak.
  • Low sensor batteries.
  • Replace sensor batteries.

9. Specifications

Model Number:10.023.35
Alarm Type:Standalone Alarm
Alarm Volume:105 dB
PIR Detection Range:Up to 8 meters
Power Source:Battery Powered (4x AA batteries, included)
Entry/Exit Delay:Yes
Dimensions (L x W x H):0.26 x 0.18 x 0.08 cm (Product); 210 grams
Material:Plastic
Color:White

10. Warranty and Support

For warranty information or technical support, please refer to the documentation provided with your purchase or contact Smartwares customer service directly. Keep your proof of purchase for warranty claims.

© 2023 Smartwares. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.