Introduction
The Vansky Motion Activated Bed Light is designed to provide a warm, soft glow to guide you safely in the dark. Featuring a smart sensor that detects both light and movement, it illuminates only when needed, promoting energy efficiency and minimizing disturbance. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting to ensure optimal performance of your bed light.
What's Included
- 1 x Vansky Motion Sensor Bed Light LED strip (5ft)
- 1 x Motion and light sensor
- 1 x Power adapter for 100V-240V (4.6ft)
- 1 x Extension cable (3.5ft)
- 1 x User manual
Setup Instructions
Follow these steps for proper installation of your Vansky Motion Activated Bed Light:
- Prepare the Surface: Clean the area under your bed frame where the LED strip will be attached. Ensure it is free from dust and debris to allow for proper adhesion.
- Apply the LED Strip: Remove the 3M adhesive backing from the LED strip. Carefully stick the LED strip along the desired location under your bed frame.
- Connect Components: Connect the LED strip to the motion and light sensor. Then, connect the power adapter to the sensor and plug it into a power outlet. An extension cable is provided for additional reach if needed.
Image: Vansky LED light strip, ready for installation.
Image: Connection diagram for the Vansky Bed Light components.
Video: Official Vansky product video demonstrating the features and installation of the motion activated bed light.
Operating Instructions
The Vansky Motion Activated Bed Light is designed for automatic operation based on movement and ambient light conditions.
- Motion Activation: The built-in human body passive infrared (PIR) motion sensor detects movement within an inductive range of 3.6 meters (11.8 feet) and a 100° angle. The light will automatically turn on when motion is detected in a dark environment.
- Automatic Shut-Off Timer: The auto shut-off timer can be adjusted from 30 seconds to 10 minutes. The light will remain on as long as continuous motion is detected and will turn off automatically after the set time once no motion is detected.
- Light Sensation: The bed light is equipped with a light sensor. It will only activate in very dark environments and will not operate if it senses sufficient ambient light.
Image: The Vansky bed light illuminating the floor when a foot touches down.
Image: Vansky Motion Activated Bed Light in use, providing illumination for safe movement.
Maintenance
To ensure the longevity and optimal performance of your Vansky Motion Activated Bed Light, follow these simple maintenance guidelines:
- Cleaning: Gently wipe the LED strip and sensor with a soft, dry cloth to remove any dust or dirt. Avoid using abrasive cleaners or solvents.
- Water and Dust Resistance: The product has an IP65 dustproof and waterproof rating, meaning it is protected against dust ingress and low-pressure water jets. However, it is not designed for submersion. Avoid direct exposure to heavy water streams.
- Adhesive Check: Periodically check the adhesive on the LED strip to ensure it remains securely attached to the bed frame. Re-secure if necessary.
Troubleshooting
If you encounter any issues with your Vansky Motion Activated Bed Light, refer to the following common troubleshooting tips:
- Light Not Turning On:
- Ensure all connections (power adapter, sensor, LED strip) are securely plugged in.
- Verify that the input and output cables are connected correctly to the motion sensor. Incorrect connection will prevent proper function.
- Check the ambient light. The light will only activate in dark environments. If the room is not dark enough, the sensor will prevent activation.
- Confirm the power outlet is functional.
- Light Not Turning Off:
- Ensure there is no continuous motion within the sensor's range.
- Check the timer setting on the sensor. Adjust it to a shorter duration if the light stays on for too long.
- Sensor Sensitivity:
- The sensor's sensitivity is fixed. Ensure the sensor is positioned optimally to detect desired motion without false triggers.
Image: Important note on connecting the motion sensor correctly.
Specifications
| Feature | Detail |
|---|---|
| Model Number | VS-BEDL1 |
| LED Quantity | 45 LEDs (5ft strip) |
| Color Temperature | 2700-3000K (Warm White) |
| Output | 12V/0.5A |
| Sensor Accommodation Time | 30 seconds - 10 minutes (adjustable) |
| Dustproof & Waterproof Grade | IP65 |
| Inductive Range | 3.6m (11.8 feet), 100° |
| Power Source | Electric |
| Voltage | 240 Volts |
| Wattage | 5 watts |
| Item Weight | 6.38 ounces |
| Product Dimensions | 5 x 4.5 x 1.5 inches |
Warranty and Support
Vansky stands behind the craftsmanship of its products. The Vansky Motion Activated Bed Light comes with a 45-day money-back guarantee and a one-year warranty.
For any questions, concerns, or support needs, please contact Vansky customer service. Refer to the product packaging or the official Vansky website for the most current contact information.
