1. Introduction
Thank you for choosing the TECKNET Wireless Doorbell. This manual provides detailed instructions for the installation, operation, and maintenance of your new doorbell system. Designed for convenience and reliability, this system features a 400-meter wireless range, IP65 waterproof rating, multiple melodies, and adjustable volume levels to suit various environments.
Image 1.1: Overview of the TECKNET Wireless Doorbell system highlighting its 400-meter wireless range. The image shows the doorbell button and receiver in a modern home setting by the sea.
2. Package Contents
Please check the package contents to ensure all items are present:
- 1 x Waterproof Transmitter (Doorbell Button)
- 2 x Plug-in Receivers (Chime Units)
- 1 x CR2032 Battery (pre-installed in transmitter)
- Mounting Hardware (screws, anchors, double-sided adhesive tape)
- User Manual
3. Setup and Installation
3.1. Receiver Installation
- Plug the receiver unit into a standard electrical outlet in your desired location. Ensure the outlet is easily accessible and not obstructed.
- For optimal performance, place receivers centrally within your home to maximize signal coverage.
3.2. Transmitter Installation
The transmitter can be installed using either the provided double-sided adhesive tape or screws.
Method 1: Adhesive Tape Installation
- Clean the mounting surface thoroughly to ensure it is dry and free of dust or grease.
- Peel off one side of the double-sided adhesive tape and attach it to the back of the transmitter.
- Peel off the other side of the tape and firmly press the transmitter onto the desired location next to your entrance door for at least 30 seconds.
Method 2: Screw Installation
- Open the transmitter casing carefully using a small screwdriver to reveal the mounting holes.
- Mark the positions for drilling on the wall.
- Drill two holes and insert the provided wall anchors.
- Secure the transmitter base to the wall using the screws.
- Reattach the front cover of the transmitter.
Image 3.1: Step-by-step guide for mounting the doorbell transmitter using either adhesive tape or screws.
4. Operating Instructions
4.1. Changing Melodies
The doorbell offers 60 different melodies. To change the melody:
- Press the 'Music Selection' button on the side of the receiver to cycle through the available melodies.
- Once you hear your preferred melody, stop pressing the button. The doorbell will remember your selection.
4.2. Adjusting Volume
There are 5 adjustable volume levels, ranging from 0dB (mute) to 110dB.
- Press the 'Volume Control' button on the side of the receiver to adjust the volume level.
- Each press will cycle through the 5 levels.
4.3. Mute Mode and LED Indicator
The doorbell features a mute mode (0dB) and a blue LED indicator for visual alerts.
- When the volume is set to 0dB, the doorbell is in mute mode, providing only a visual LED flash when the button is pressed. This is useful for quiet environments or for individuals with hearing impairments.
- The blue LED on the receiver will flash when the doorbell is activated, providing a clear visual signal.
Image 4.1: Visual representation of the doorbell's features including 60 melodies, 5 volume levels, and 3 operating modes.
Image 4.2: The doorbell receiver operating in mute mode, ideal for maintaining quiet environments.
5. Maintenance
5.1. Battery Replacement (Transmitter)
The transmitter uses one CR2032 battery, which has an estimated lifespan of 4.5 years. When the doorbell button no longer activates the chime, it may be time to replace the battery.
- Carefully open the transmitter casing.
- Remove the old CR2032 battery.
- Insert a new CR2032 battery, ensuring correct polarity.
- Close the casing securely.
5.2. Cleaning
To maintain the appearance and functionality of your doorbell:
- Wipe the transmitter and receiver with a soft, damp cloth.
- Do not use abrasive cleaners or solvents, as these can damage the surface.
Image 5.1: The doorbell's IP65 waterproof rating, wide operating temperature range, and long battery life for the transmitter.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Doorbell does not chime. |
|
|
| Interference from other devices. |
|
|
| Shortened wireless range. |
|
|
7. Specifications
| Model Number | 841584 |
| Wireless Range | Up to 400 meters (1300 feet) in open areas |
| Waterproof Rating | IP65 (Transmitter) |
| Melodies | 60 selectable melodies |
| Volume Levels | 5 levels (0dB to 110dB) |
| Operating Temperature | -20°C to 60°C (-4°F to 140°F) |
| Transmitter Battery | 1 x CR2032 (included) |
| Receiver Power | AC 220V (Plug-in) |
| Transmitter Dimensions | 7.2 cm x 4.2 cm |
| Receiver Dimensions | 8.6 cm x 7.4 cm |
| Product Weight | 251 grams |
Image 7.1: Detailed view of the transmitter and receiver, including their dimensions and the location of control buttons.
8. Warranty and Support
8.1. Warranty Information
TECKNET offers a 36-month warranty for this product, subject to registration. Please refer to the warranty card included in your package for registration details and terms and conditions. This warranty covers manufacturing defects and ensures long-term reliability.
8.2. Return Policy
A hassle-free 30-day return policy is provided for your peace of mind. If you are not satisfied with your purchase within 30 days, please contact your retailer for return options.
8.3. Customer Support
For any questions, technical assistance, or warranty claims, please contact TECKNET customer support. Contact information can typically be found on the TECKNET official website or on the product packaging.
