1. Introduction
This manual provides essential information for the proper installation, operation, and maintenance of your Glixal ATKS-037 Reinforced Racing CVT Drive Belt. This drive belt is designed for 4-stroke GY6 125cc and 150cc (157QMJ/152QMI) long case engines commonly found in scooters, mopeds, ATVs, and go-karts. Adhering to these instructions will help ensure optimal performance and longevity of the product.

Image 1.1: The Glixal ATKS-037 Reinforced Racing CVT Drive Belt, showcasing its robust construction.
2. Safety Information
Always prioritize safety when working with vehicle components. Failure to follow safety guidelines can result in injury or damage to the vehicle.
- Ensure the vehicle is turned off, cooled down, and secured on a stable surface before beginning any work.
- Wear appropriate personal protective equipment (PPE), including gloves and eye protection.
- Refer to your vehicle's specific service manual for detailed instructions on accessing and replacing CVT components.
- Keep hands and clothing clear of moving parts during any testing or operation.
- Dispose of old parts responsibly according to local regulations.
3. Setup & Installation
Proper installation of the CVT drive belt is crucial for performance and durability. This section outlines the general steps; consult your vehicle's service manual for specific procedures.
3.1 Compatibility Check
Before installation, verify that the Glixal ATKS-037 belt is compatible with your engine. This belt is designed for 4-stroke GY6 125cc and 150cc (157QMJ/152QMI) long case engines. Confirm the dimensions match your original belt or the required specifications for your vehicle:
- Length: 842mm
- Width: 20mm
- Teeth Angle: 30 degrees
Small deviations in size can sometimes work, but it is recommended to stay within a few millimeters on length, 0.5mm or less on width, and within 2 degrees for the teeth angle for optimal fit and performance. Always compare to your old belt to ensure correctness before ordering and installing.

Image 3.1: Important note regarding belt size comparison for proper fitment.
3.2 General Installation Steps
- Access the CVT Cover: Locate and remove the CVT cover on your scooter, moped, ATV, or go-kart. This typically involves removing several bolts.
- Remove Old Belt: Carefully remove the old drive belt. Note its orientation and how it sits on the variator and clutch pulleys.
- Inspect Components: While the CVT cover is off, inspect the variator, clutch, and other related components for wear, damage, or debris. Clean as necessary.
- Install New Belt: Place the new Glixal ATKS-037 belt onto the variator and clutch pulleys. Ensure it is seated correctly and not twisted. The belt should have the branding facing outwards (if applicable).
- Reassemble: Reinstall the CVT cover, ensuring all bolts are tightened to the manufacturer's specifications.

Image 3.2: Example of a GY6 150cc engine, showing the general location of the CVT system.
4. Operation
The Glixal ATKS-037 CVT drive belt is designed to provide reliable power transfer in your vehicle's continuously variable transmission system. While the belt itself does not require specific operational steps beyond proper installation, it is important to understand its function and initial break-in period.
4.1 Initial Break-in
After installing a new drive belt, it is recommended to follow a gentle break-in procedure for the first 50-100 miles. Avoid aggressive acceleration, sudden braking, and prolonged high-speed operation during this period. This allows the belt to properly seat and conform to the variator and clutch pulleys, maximizing its lifespan and performance.
5. Maintenance
Regular inspection and timely replacement are key to maintaining the performance and safety of your vehicle's CVT system.
5.1 Inspection Schedule
Inspect the drive belt every 1,000-2,000 miles or as recommended by your vehicle's manufacturer. Look for the following signs of wear:
- Cracks or Fraying: Visible cracks, tears, or fraying along the edges or surface of the belt.
- Glazing: A shiny, hardened appearance on the belt's surface, indicating slippage and heat buildup.
- Missing Teeth: Any missing or damaged teeth along the inner surface.
- Excessive Wear: The belt appears thinner than its original 20mm width, indicating material loss.

Image 5.1: Close-up view of the belt's teeth, which should be regularly inspected for wear.
5.2 Replacement
Replace the drive belt immediately if any signs of significant wear or damage are observed. A worn belt can lead to reduced performance, slippage, and potential failure, which can cause further damage to other CVT components or leave you stranded. The typical replacement interval for a CVT belt is between 3,000-6,000 miles, but this can vary based on riding conditions and maintenance habits.
6. Troubleshooting
If you experience issues with your vehicle's CVT system, the drive belt may be a contributing factor. Here are some common problems and potential solutions:
| Symptom | Possible Cause | Solution |
|---|---|---|
| Loss of power or acceleration | Worn or slipping belt, incorrect belt size, worn variator/clutch components | Inspect belt for wear; replace if necessary. Verify correct belt size. Inspect variator and clutch. |
| Squealing or grinding noise from CVT | Worn belt, debris in CVT housing, worn bearings in variator/clutch | Inspect and clean CVT housing. Replace worn belt or bearings. |
| Belt breaking prematurely | Incorrect belt tension, misaligned pulleys, worn variator/clutch, aggressive riding style, manufacturing defect | Ensure proper installation. Inspect other CVT components. Contact Glixal support if defect is suspected. |
| Vibration or rough operation | Uneven belt wear, damaged variator rollers, unbalanced clutch | Inspect belt for uneven wear. Check variator rollers and clutch for balance and wear. |
7. Specifications
- Model: ATKS-037
- Material: Fiber + Rubber (for enhanced durability and performance)
- Length: 842mm
- Width: 20mm
- Teeth Angle: 30 degrees
- Compatible Engines: 4-stroke GY6 125cc, 150cc (157QMJ/152QMI) Long Case Engines
- Compatible Vehicles: Scooters, Mopeds, ATVs, Go Karts
- Manufacturer Part Number: ATKS-037
- Item Weight: Approximately 5.6 ounces
- Product Dimensions: 33.15 x 0.79 x 0.04 inches (approximate, referring to L x W x H of packaged item)

Image 7.1: Close-up of the Glixal belt showing the 842-20-30 size marking.
8. Warranty and Support
For any questions regarding the Glixal ATKS-037 Reinforced Racing CVT Drive Belt, including installation assistance, troubleshooting, or warranty inquiries, please contact Glixal customer support through the retailer where the product was purchased or visit the official Glixal website for contact information. Please have your purchase details and product model number (ATKS-037) available when contacting support.