Giro Foray Cycling Helmet Instruction Manual

1. Introduction

The Giro Foray Cycling Helmet is designed for cyclists seeking a blend of performance, comfort, and protection. It incorporates durable in-mold construction and the Roc Loc 5 fit system for a secure and adjustable fit. This manual provides essential information for the proper use, adjustment, and maintenance of your helmet.

Key features of the Giro Foray Cycling Helmet include:

• Market-Leading Protection: Engineered in Giro’s helmet test lab.
• Ventilation: 21 Wind Tunnel vents with internal channeling for airflow.
• Comfort: Roc Loc 5 fit system for easy vertical position and tension adjustment.
• Adjustable Fit: Universal Fit designed for broad compatibility.
• Lightweight: In-mold construction contributes to a light design.

2. Safety Information

Always wear a helmet when cycling. A helmet cannot protect against all possible impacts. For maximum protection, the helmet must fit properly and all retention straps must be securely fastened. Inspect your helmet regularly for signs of wear or damage. Replace your helmet immediately after any impact, even if visible damage is not apparent, as its protective capabilities may be compromised. Do not modify the helmet or use it for activities other than cycling.

3. Setup and Fitting

Proper helmet fit is crucial for safety and comfort. Follow these steps to ensure your Giro Foray helmet is correctly adjusted:

1. Positioning the Helmet: Place the helmet on your head so that it sits level and covers your forehead. The front edge of the helmet should be approximately one to two finger-widths above your eyebrows.
2. Adjusting the Roc Loc 5 Fit System: The Roc Loc 5 system allows for both vertical position and tension adjustment. Use the dial at the back of the helmet to tighten or loosen the fit until the helmet feels snug but comfortable, without excessive pressure points. The helmet should not move significantly when you shake your head.
3. Adjusting the Straps:
   • Side Straps: Adjust the sliders on the side straps so that they form a 'V' shape just below your ears.
   • Chin Strap: Fasten the chin strap buckle. Tighten the strap until it is snug under your chin. You should be able to open your mouth wide, but the helmet should not slide forward or backward.
4. Final Check: With the straps fastened and the fit system tightened, try to move the helmet from side to side and front to back. It should feel secure and not shift excessively.

Image: A side view of the Giro Foray Cycling Helmet, showcasing its aerodynamic design and ventilation ports.

4. Operating (Wearing the Helmet)

Once your helmet is properly adjusted according to the setup instructions, ensure it is worn correctly every time you cycle. The helmet should remain level on your head, covering your forehead, and the straps should be comfortably snug. Periodically check the fit during rides, especially after long periods of use or if you notice any discomfort or movement.

5. Maintenance

Proper care will extend the life of your helmet and maintain its protective qualities.

• Cleaning: Clean the helmet exterior with a soft cloth, mild soap, and cool water. Avoid harsh chemicals, abrasive cleaners, or solvents, as these can damage the helmet's materials.
• Interior Pads: The interior padding can be removed and hand-washed with mild soap and water, then air-dried. Ensure pads are completely dry before reinserting them into the helmet.
• Storage: Store your helmet in a cool, dry place away from direct sunlight and extreme temperatures. Avoid storing it near heat sources or in enclosed spaces like car trunks on hot days, as excessive heat can damage the helmet's liner.
• Inspection: Regularly inspect the helmet shell, liner, and straps for any cracks, dents, fraying, or other signs of wear or damage. If any damage is found, replace the helmet.

6. Troubleshooting

• Helmet feels loose or shifts: Re-adjust the Roc Loc 5 fit system dial to tighten the fit. Ensure the chin strap is snug and the side strap sliders are positioned correctly below your ears.
• Discomfort or pressure points: Loosen the Roc Loc 5 fit system slightly. Check the positioning of the helmet on your head; it should be level. Ensure no hair or accessories are interfering with the fit.
• Straps are twisted: Unbuckle the chin strap and untwist the straps. Re-adjust the side sliders and chin strap for a flat, comfortable fit.
• Excessive sweating: While the helmet has 21 vents, individual experiences may vary. Ensure the helmet is clean and the vents are unobstructed. Consider wearing a moisture-wicking skull cap if needed.

7. Specifications

8. Warranty Information

Any Giro helmet determined by Giro to be defective in materials or workmanship within one (1) year from the date of original purchase will be repaired or replaced, at Giro’s option, free of charge when received at the factory freight prepaid, together with proof of purchase.

9. Customer Support

For further assistance, questions, or to learn more about Giro products, please visit the official Giro store or contact their customer service department. You can find more information at the Giro Brand Store.