Introduction
This manual provides essential instructions for the installation, operation, and maintenance of the Red Lion 305584014 Replacement Pressure Switch Kit. This kit is specifically designed for use with all Red Lion RJS-PREM series shallow well jet pumps. Proper installation and maintenance are crucial for optimal performance and longevity of your pump system.
Product Overview
The Red Lion 305584014 Pressure Switch Kit is a repair kit containing the necessary components to replace the pressure switch on your RJS-PREM series shallow well jet pump. It includes the pressure switch, tubing, and plastic fasteners.
- Pressure Switch Kit: Contains the pressure switch, tubing, and plastic fasteners for the RJS-PREM Series shallow well jet pumps.
- Repair Kit: Designed specifically for the Red Lion RJS-PREM series shallow well jet pumps; not recommended for use with other jet pumps as connections may not fit.
- Contents: Pressure switch, tubing, and plastic connectors.
- Parts List Reference: Refer to the owner's manual for the pump's parts list image, which contains item #'s 1 and 13.
- Installation Instructions: For detailed installation instructions, refer to the pump's original installation manual.
Kit Components
Safety Information
Always disconnect power to the pump before performing any maintenance or installation. Failure to do so can result in serious injury or death. Ensure all electrical connections are secure and properly insulated. Consult a qualified electrician or plumber if you are unsure about any steps.
This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
Setup and Installation
This pressure switch kit is a replacement part. Refer to your pump's original installation manual for specific instructions on how to replace the pressure switch. The general steps involve:
- Disconnect Power: Ensure the pump is completely disconnected from the electrical power source.
- Drain System: Drain the pump and associated plumbing to relieve pressure and prevent water spillage.
- Remove Old Switch: Carefully disconnect the electrical wiring and the pressure sensing tube from the old pressure switch. Note the wire connection locations for reassembly.
- Install New Switch: Attach the new pressure switch to the pump, ensuring the pressure sensing tube is securely connected. Reconnect the electrical wiring according to the original configuration.
- Prime Pump: Before restarting, properly prime the pump by filling it with water as per your pump's manual.
- Test System: Restore power and check for proper operation and any leaks.
Installation Video Guide
Video: "How to Replace a Jet Pump Pressure Switch" by Franklin Electric - Little Giant. This video demonstrates the step-by-step process of replacing a pressure switch on a jet pump, including electrical disconnections, physical removal, and reinstallation of the new switch and tubing.
Operating Instructions
Once the pressure switch kit is installed and the pump is primed, the pressure switch will automatically regulate the pump's operation based on the system's pressure. It will activate the pump when pressure drops below a set point and deactivate it when the desired pressure is reached. Ensure the pump is connected to a suitable power source and that all valves are open for proper water flow.
Maintenance
Regular inspection of the pressure switch and its connections is recommended. Check for any signs of wear, corrosion, or leaks. Ensure the electrical connections remain tight and free from debris. If any damage is observed, replace the affected components immediately. Periodically check the pressure settings to ensure they align with your system's requirements.
Troubleshooting
If your pump is not operating correctly after replacing the pressure switch, consider the following:
- Pump Not Starting: Check electrical connections for tightness. Ensure the pump is properly primed. Verify power supply to the pump.
- Pump Running Continuously: Inspect for leaks in the plumbing system or a faulty check valve. The pressure switch might not be sensing pressure correctly due to air in the line or a blockage.
- Frequent Cycling: This could indicate a small leak in the system or a problem with the pressure tank.
- Leaks at Connections: Ensure all connections, especially the plastic fasteners, are tightened appropriately. Teflon tape or pipe sealant may be required for threaded connections.
For further assistance, refer to your pump's comprehensive owner's manual or contact Red Lion customer support.
Specifications
| Feature | Detail |
|---|---|
| Brand | Red Lion |
| Model Number | 305584014 |
| Item Type Name | 305584014 Pressure Switch Kit for All RJS-PREM Shallow Well Jet Pump Models |
| Color | Black |
| Material | Plastic, Stainless Steel |
| Product Dimensions (L x W x H) | 3.5"L x 8"W x 11"H |
| Item Weight | 0.01 Ounces |
| Included Components | Hose, Plastic Fasteners, Pressure Switch |
| Manufacturer | Franklin Electric Canada, Inc. |
Warranty and Support
The Red Lion 305584014 Pressure Switch Kit comes with a 1-year manufacturer's warranty. For warranty claims or technical support, please refer to the contact information provided in your pump's owner's manual or contact Franklin Electric - Little Giant directly.
Frequently Asked Questions (FAQs)
- Do you support your products? Yes, our staff are able to assist with troubleshooting or installation assistance.
- 30 Day Return Policy: For items purchased within 30 days, please refer to Amazon's 30-day return policy.
- After 30 Days: Please check your invoice or order. If the seller indicates a company other than Amazon.com, please contact the seller directly for more information. If Amazon.com is the seller, your product is covered by the terms outlined in our manual. Please refer to your owner's manual for more information.
For additional support, you can visit the Red Lion Store on Amazon.
