1. Introduction
The BTF-LIGHTING 5050 RGBW LED Tape Light is a versatile lighting solution featuring 4 colors in 1 LED (Red, Green, Blue, and Warm White 2700K-3000K). This 5-meter (16.4ft) strip, with 60 LEDs per meter, offers a wide range of colors and dimmable pure white light for various decorative applications. This manual will guide you through the setup, operation, and maintenance of your LED tape light.
Figure 1: Key features of the BTF-LIGHTING 5050 RGBW LED Tape Light.
2. Safety Information
- This LED tape light operates on DC12V. Ensure your power supply is compatible to prevent damage.
- The IP30 rating indicates this product is non-waterproof. Avoid exposure to moisture or liquids.
- Do not light up the maximum brightness mixed white light for extended periods to prevent overheating and ensure longevity.
- Ensure all wiring connections are secure and correctly polarized (+12V-G-R-W-B) to avoid short circuits or damage.
- Keep out of reach of children. The strip is touchable and safe under normal operating conditions.
3. Package Contents
Please verify that all items are present in your package:
- 1 x BTF-LIGHTING 5050 RGBW 4-in-1 LED Strip Light (5 meters / 16.4 feet)
- 1 x 5-Pin Connector (for wiring)
Note: A DC12V power supply and a compatible RGBW controller are required for operation and are not included in this package. These must be purchased separately.
Figure 2: Package contents and example of strip connection.
4. Specifications
| Feature | Detail |
|---|---|
| Model Number | RGBWW45M505060LW30 |
| LED Type | 5050 RGBW (4 colors in 1 LED) |
| Color Temperature (Warm White) | 2700K-3000K |
| Length | 5 meters (16.4 ft) |
| LED Quantity | 60 LEDs/meter (300 RGB LEDs + 300 Warm White LEDs total) |
| Input Voltage | DC12V |
| Power Consumption | 0.1-0.4W/LED, 6W-24W/meter, Total: 30W-120W (variable) |
| Recommended Power Supply | DC12V 10A 120W |
| FPCB Width | 12mm (White PCB) |
| Waterproof Level | IP30 (Non-waterproof) |
| Cuttable | Every 3 LEDs |
| Connector | 5 Pin (+12V G R B W) |
| Lifespan | >50,000 hours |
Figure 3: High-quality 5050 RGBW LED chip design.
Figure 4: LED contrast: 4-in-1 RGBW vs. separate RGB and Warm White LEDs.
5. Setup and Installation
5.1 Preparation
Before installation, ensure you have the following components (not included):
- DC12V Power Supply (Recommended: 12V 10A 120W)
- Compatible RGBW LED Controller (e.g., Tuya Zigbee, Bluetooth APP, WiFi Alexa Google Home, RF Remote controllers)
5.2 Cutting and Linking
The LED strip is flexible and can be cut to your desired length. Cut points are located every 3 LEDs. Use the designated cut marks on the strip. The strip features 5-Pin connectors on both ends (one male, one female) to support end-to-end connection for extending the length.
Figure 5: LED strip features including adhesive backing and cut points.
5.3 Wiring Connections
Connect the LED strip to your RGBW controller and DC12V power supply. The correct PIN order for the strip is +12V-G-R-W-B. Ensure that the wires from the strip are connected to the corresponding pins on your controller. Pay close attention to the polarity and color coding to avoid incorrect operation or damage.
5.4 Mounting the LED Strip
The IP30 non-waterproof version of this LED strip comes with double-sided adhesive tape on the back for easy installation. Ensure the mounting surface is clean, dry, and smooth. Apply firm pressure along the entire length of the strip to activate the pressure-sensitive adhesive for optimal adhesion.
Video 1: Demonstration of the BTF-LIGHTING RGBW 5050SMD 4-in-1 LED strip light in operation, showcasing various colors and brightness levels.
6. Operating Instructions
6.1 Power On/Off
Once properly connected to a power supply and controller, use your RGBW controller to power the LED strip on or off.
6.2 Color and Brightness Control
The 4-in-1 RGBW LEDs allow for a vast spectrum of colors. Use your compatible RGBW controller to:
- Select from 16 million different colors by mixing Red, Green, and Blue channels.
- Adjust the brightness of any selected color or white light from 1% to 100%.
- Activate the dedicated Warm White (2700K-3000K) channel for energy-efficient pure white illumination.
6.3 Dynamic Modes
Many RGBW controllers offer various dynamic modes such as flashing, fading, or color cycling. Refer to your specific controller's manual for instructions on activating and customizing these modes.
6.4 Controller Compatibility
This LED strip is compatible with a wide range of RGBW controllers, including:
- Tuya Zigbee 3.0 Controllers (e.g., LM052, C04Z)
- Bluetooth APP Controllers (e.g., LM053)
- WiFi Alexa Google Home Controllers (e.g., WB5, C04W)
- RF Remote Controllers (e.g., RC03RFB + 1XC04RF)
Figure 6: Examples of compatible BTF-LIGHTING LED controllers.
7. Maintenance
7.1 Cleaning
To clean the LED strip, gently wipe it with a dry, soft cloth. Do not use abrasive cleaners or solvents. Ensure the strip is powered off and disconnected from the power supply before cleaning.
7.2 Inspection
Periodically inspect the LED strip and its connections for any signs of wear, damage, or loose wiring. Address any issues promptly to ensure safe and optimal performance.
8. Troubleshooting
8.1 No Light
- Check Power Supply: Ensure the DC12V power supply is correctly connected and functioning.
- Check Controller Connection: Verify that the LED strip is securely connected to the RGBW controller.
- Verify Wiring: Confirm that the 5-Pin connector wires are correctly matched to the controller's output (PIN Order: +12V-G-R-W-B). Incorrect polarity can prevent the strip from lighting up.
8.2 Incorrect Colors or Missing Colors
- Check Wiring: This is often caused by incorrect wiring of the G (Green) and R (Red) pins. Double-check that the green wire from the strip is connected to the green output on the controller, and the red wire to the red output.
- Controller Settings: Ensure your RGBW controller is set to the correct output mode for RGBW strips.
8.3 Dim or Flickering Lights
- Insufficient Power: Ensure your DC12V power supply has sufficient wattage (Recommended: 120W) for the entire length of the LED strip.
- Voltage Drop: For very long runs, voltage drop can occur. Consider powering the strip from both ends or adding power injection points if experiencing dimming towards the end of the strip.
- Loose Connections: Check all connections for tightness.
9. Warranty Information
This BTF-LIGHTING LED Tape Light comes with a one-year warranty from the date of purchase. The warranty covers manufacturing defects under normal use. Please retain your proof of purchase for warranty claims. The warranty does not cover damage resulting from improper installation, misuse, unauthorized modifications, or exposure to conditions beyond the product's specifications (e.g., water damage for IP30 products).
10. Customer Support
If you encounter any issues or have questions not covered in this manual, please contact BTF-LIGHTING customer service for assistance. For the most up-to-date contact information, please visit the official BTF-LIGHTING website or refer to your purchase documentation.
