Kokido Krill C/02 Automatic Pool Cleaner Instruction Manual

1. Product Overview

The Kokido Krill C/02 is an automatic pool cleaner designed for pools up to 6 meters in diameter with low filter flow rates. It features a cleaning head, an 8-meter hose, a 0.75-liter internal filter, and a new generation membrane for quiet operation. Integrated pre-filters collect debris, and the filter is easily cleaned via a rotatable opening. The cleaner includes compatible connections for most standard pools, along with a float and weight for optimal positioning.

Key Features:

• Suitable for pools up to 6 meters in diameter with low filter flow.
• Connections compatible with most standard pools.
• New generation diaphragm ensures quiet operation.
• Integrated pre-filter for efficient dirt collection.
• Easy filter cleaning thanks to the rotatable opening.

Image: The Kokido Krill C/02 Automatic Pool Cleaner, showing its main components including the cleaning head and hose.

2. Setup Instructions

1. Unpack Components: Carefully remove all components from the packaging. Verify that all parts are present: cleaning head, 8-meter hose, internal filter, float, and weight.
2. Assemble Cleaning Head: Attach the cleaning head components as per the diagrams in the included quick-start guide (if applicable). Ensure all connections are secure.
3. Install Internal Filter: Insert the 0.75-liter internal filter into the designated compartment within the cleaning head. Ensure it is properly seated and the rotatable opening is accessible for future cleaning.
4. Connect Hose: Connect the 8-meter hose to the cleaning head. Then, connect the other end of the hose to your pool's skimmer or dedicated suction line. Ensure all hose connections are tight to prevent air leaks.
5. Adjust Float and Weight: Position the float and weight along the hose according to your pool's depth and the cleaner's movement requirements. This helps optimize the cleaner's balance and coverage.
6. Submerge Cleaner: Slowly lower the cleaner into the pool, allowing it to fill with water and sink to the bottom. Ensure no air is trapped inside the cleaner or hose.
7. Start Filtration System: Once the cleaner is fully submerged and connected, turn on your pool's filtration system. The cleaner will begin to operate as suction is established.

3. Operating Instructions

The Kokido Krill C/02 operates automatically once connected to your pool's filtration system and submerged. It utilizes the suction from your pool pump to move across the pool floor and walls, collecting debris.

• Automatic Operation: The cleaner will move randomly across the pool surface, driven by the suction. Its new generation membrane ensures quiet operation, minimizing disturbance.
• Debris Collection: Integrated pre-filters within the cleaning head are designed to capture dirt, leaves, and other small debris before they reach your main pool filter.
• Optimal Performance: For best results, ensure your pool pump is running at an adequate flow rate. The cleaner is optimized for pools up to 6 meters in diameter with low filter flow.
• Monitoring: Periodically observe the cleaner's movement to ensure it is covering the entire pool area. Adjust the hose length or float/weight positions if necessary to improve coverage.

4. Maintenance

Regular maintenance ensures the longevity and efficient operation of your Kokido Krill C/02 pool cleaner.

1. Filter Cleaning: The internal filter should be cleaned regularly, especially after each cleaning cycle or when you notice a decrease in cleaning performance. To clean, remove the filter via the rotatable opening and rinse thoroughly with a garden hose. Reinstall once clean.
2. Hose Inspection: Periodically inspect the 8-meter hose for any kinks, cracks, or blockages. A damaged hose can impair suction and cleaner movement. Replace if necessary.
3. Cleaning Head Check: Ensure the cleaning head is free from obstructions. Remove any large debris that may have become lodged in the intake or moving parts.
4. Storage: When not in use for extended periods, clean the unit thoroughly, disconnect the hose, and store the cleaner in a cool, dry place away from direct sunlight and harsh chemicals.

5. Troubleshooting

If your Kokido Krill C/02 is not performing as expected, refer to the following common issues and solutions:

• Cleaner is not moving or moving slowly:
  • Check for blockages in the cleaning head or hose.
  • Ensure the internal filter is clean and not clogged.
  • Verify that the pool pump is running and providing adequate suction.
  • Check for air leaks in the hose connections.
• Cleaner gets stuck in corners or specific areas:
  • Adjust the position of the float and weight on the hose to change the cleaner's balance and movement pattern.
  • Ensure the hose length is appropriate for your pool size, allowing sufficient slack without excessive tangling.
• Cleaner is not picking up debris effectively:
  • Clean the internal filter thoroughly.
  • Check for any large debris obstructing the intake opening of the cleaning head.
  • Ensure the pool pump's suction is strong enough.
• Cleaner stops frequently:
  • This often indicates a clogged filter or an obstruction. Clean the filter and check for blockages.
  • Ensure the weight is properly secured and not shifting, which can affect the cleaner's operation.

6. Specifications

7. Warranty Information

Specific warranty details for the Kokido Krill C/02 Automatic Pool Cleaner are not provided in this manual. For information regarding product warranty, please refer to the documentation included with your purchase or contact the retailer or manufacturer directly.

8. Support

For further assistance, technical support, or inquiries about your Kokido Krill C/02 Automatic Pool Cleaner, please contact your point of purchase or the Kokido customer service department. Contact information may be available on the product packaging or the official Kokido website.