Introduction
The Power Acoustik EG1-10000D is a high-performance Class D monoblock amplifier designed for car audio systems. This manual provides essential information for the proper installation, operation, and maintenance of your amplifier to ensure optimal sound quality and product longevity. Please read all instructions carefully before attempting installation or operation.
Safety Information
Important Safety Warnings:
- This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
- Ensure the amplifier receives the correct electrical supply current. Insufficient current (below 400-600 amps of 14V DC) can lead to overheating and potential failure. Proper wiring, batteries, connectors, and capacitors are crucial.
- The output circuit must maintain a minimum 1 Ohm load. Operating below this impedance can trigger the protection circuit.
- Continuously activating the protection circuit due to incorrect installation or impedance can cause excessive heat and shorten the product's lifespan.
- Always disconnect the vehicle's battery before performing any electrical work.
Package Contents
Verify that all items are present in the package:
- Power Acoustik EG1-10000D Monoblock Amplifier
- Owner's Manual
- Dash Mount Remote Bass Control Knob
- Mounting Hardware (screws, etc.)
Setup and Installation
Proper installation is critical for the performance and longevity of your amplifier. It is recommended that installation be performed by a qualified professional.
Mounting the Amplifier
The EG1-10000D is designed for surface mounting. Choose a location that provides adequate ventilation and is protected from moisture and direct sunlight. Ensure the mounting surface is secure and can support the amplifier's weight.
- Select a suitable mounting location.
- Use the amplifier as a template to mark the mounting screw holes.
- Drill pilot holes if necessary.
- Secure the amplifier using the provided mounting hardware.
Electrical Connections
The amplifier requires a robust electrical system to deliver its rated power. Ensure your vehicle's electrical system can provide 400-600 amps of 14V DC current. This includes appropriate gauge wiring, high-capacity batteries, and quality connectors.
- Power Input: Connect the main power cable from the battery to the amplifier's +12V terminal. Use appropriate gauge wire for the current draw.
- Ground Connection: Connect a short, heavy-gauge ground cable from the amplifier's GND terminal to a clean, unpainted metal surface on the vehicle chassis.
- Remote Turn-On: Connect a remote turn-on wire from your head unit or other switched 12V source to the amplifier's REM terminal.
- Speaker Output: Connect your subwoofer(s) to the amplifier's speaker terminals. Ensure the total impedance of the connected subwoofers is no less than 1 Ohm for stable operation.
Remote Bass Control Knob
Connect the dash mount remote bass control knob to the designated port on the amplifier. This allows for convenient adjustment of bass levels from the driver's seat.
Linking Two Monoblocks
For increased power output, two EG1-10000D amplifiers can be linked together. Refer to the detailed wiring diagrams in the full owner's manual for specific instructions on linking two units for double power.
Operating Instructions
Once properly installed, the amplifier will power on with your head unit. Adjustments can be made using the controls on the amplifier and the remote bass knob.
- Gain Control: Adjust the gain setting to match the output voltage of your head unit. Start low and gradually increase until desired volume is achieved without distortion.
- Low Pass Filter (LPF): The amplifier features a variable 12dB low pass filter. Adjust this to control the upper frequency limit of the audio signal sent to your subwoofers.
- Subsonic Filter: Utilize the variable subsonic filter to remove extremely low frequencies that are inaudible and can cause damage to subwoofers.
- Bass Boost: A 12dB bass boost feature is included to enhance low octave harmonics. Use this sparingly to avoid distortion.
- Phase Shift: An 180-degree phase shift control improves low octave dynamics and helps blend the subwoofer output with other speakers in the system.
- Remote Bass Knob: Use the dash mount remote bass control knob for real-time adjustment of the subwoofer output level.
Maintenance
To ensure the longevity and optimal performance of your Power Acoustik EG1-10000D amplifier, follow these maintenance guidelines:
- Keep the amplifier clean and free from dust and debris. Use a soft, dry cloth for cleaning.
- Ensure adequate airflow around the amplifier to prevent overheating. Do not block ventilation openings.
- Regularly check all electrical connections for tightness and corrosion. Loose connections can lead to power loss and heat buildup.
- Avoid exposing the amplifier to extreme temperatures or moisture.
Troubleshooting
If you experience issues with your amplifier, refer to the following common troubleshooting steps:
- No Power: Check all power and ground connections. Verify the remote turn-on wire is receiving 12V. Check the inline fuse on the main power cable.
- Protection Light On: This indicates an issue with the installation or operation. Common causes include:
- Insufficient electrical supply current (check wiring, battery, and charging system).
- Speaker impedance below 1 Ohm (check subwoofer wiring and impedance).
- Short circuit in speaker wiring.
- Overheating (ensure proper ventilation).
- No Sound: Check RCA input connections from the head unit. Verify speaker connections. Ensure gain settings are not too low.
- Distorted Sound: Reduce gain settings. Check for proper LPF and subsonic filter adjustments. Ensure speaker impedance is correct.
- Amplifier Gets Hot: Some heat is normal, but excessive heat indicates a problem. This is often due to insufficient electrical supply current or an impedance load below 1 Ohm. Ensure proper ventilation and correct wiring.
If problems persist after following these steps, contact Power Acoustik customer support or a qualified car audio technician.
Specifications
| Feature | Specification |
|---|---|
| Model Number | EG110000D |
| Brand | Power Acoustik |
| Output Power (RMS) | 5000 Watts @ 1 Ohm |
| Number of Channels | 1 (Monoblock) |
| Minimum Stable Impedance | 1 Ohm |
| Voltage | 14 Volts (Nominal) |
| Maximum Supply Voltage | 14 Volts |
| Bass Boost | 12dB |
| Phase Shift | 180 Degrees |
| Mounting Type | Surface Mount |
| Dimensions (L x W x H) | 24 x 11.25 x 4.25 inches |
| Item Weight | 1.05 pounds |
| UPC | 709483052840 |
| Color | White |
Warranty Information
Specific warranty terms and conditions for the Power Acoustik EG1-10000D amplifier are provided by the manufacturer. Please refer to the warranty card included with your product or visit the official Power Acoustik website for detailed information regarding coverage, duration, and claims procedures.
Customer Support
For technical assistance, troubleshooting beyond this manual, or inquiries regarding your Power Acoustik EG1-10000D amplifier, please contact Power Acoustik customer support. Contact information can typically be found on the manufacturer's official website or in the product packaging.
