1. Introduction
This instruction manual provides essential information for the proper installation, maintenance, and care of your SANWA RX-482 Receiver Case Set, model 107A41302A. Please read this manual thoroughly before proceeding with the installation to ensure correct assembly and optimal performance of your receiver.
2. Product Overview
The SANWA RX-482 Receiver Case Set is a genuine replacement part designed to house and protect the internal electronic components of your SANWA RX-482 receiver. This set includes the necessary plastic housing components and identification labels to restore your receiver's physical integrity and appearance.
Image 1: Components of the SANWA RX-482 Receiver Case Set. This image displays the two black plastic case halves, a main label for the RX-482 receiver, and a smaller label for channel identification.
3. Package Contents
Verify that all items listed below are present in your package:
- RX-482 Receiver Case (Top Half)
- RX-482 Receiver Case (Bottom Half)
- RX-482 Main Identification Label (featuring SANWA, FH4T, 2.4GHz, 92082, AIRTRONICS, SSL SYSTEM, RX-482, PUSH BIND LED)
- Channel Port Identification Label (featuring SSL/BAT, CH4, CH3, CH2, CH1)
4. Installation (Setup)
This section details the process of transferring the internal components of your existing SANWA RX-482 receiver into the new replacement case.
4.1. Tools Required
- Small Phillips Head Screwdriver
- Clean, static-free work surface
4.2. Installation Procedure
- Preparation: Ensure your work area is clean and free of static electricity. Disconnect the receiver from all power sources and connected devices.
- Open Existing Case: Carefully locate and remove any screws securing your existing RX-482 receiver case. Gently pry open the case halves.
- Remove Internal Components: With extreme care, detach the receiver's circuit board and any other internal components (e.g., antenna wires if detachable) from the old case. Avoid touching the electronic components directly with bare hands to prevent static discharge.
- Install into New Case: Place the circuit board into the bottom half of the new RX-482 Receiver Case. Ensure that all ports, LED indicators, and the bind button align correctly with the openings in the new case.
- Secure Case Halves: Carefully align the top half of the new case with the bottom half. Press them together firmly until they snap or fit securely. If screws were used in the original design, transfer and secure them. (Note: This case set may not include new screws if the original design uses snap-fit or existing screws.)
- Apply Labels: Affix the main RX-482 identification label to the designated flat surface on the top of the case. Apply the smaller channel port identification label near the corresponding ports.
- Final Check: Inspect the assembled case to ensure it is fully closed and secure. Verify that all ports are accessible and the bind button can be pressed.
5. Usage
The SANWA RX-482 Receiver Case Set serves as a protective enclosure for your receiver's electronics. Once the receiver's internal components are correctly installed within this case, the receiver will function as intended by its original design. The case itself does not alter the operational characteristics of the receiver but provides physical protection against dust, debris, and minor impacts.
6. Maintenance
- Cleaning: Use a soft, dry cloth to wipe the exterior of the case. For stubborn dirt, a slightly damp cloth can be used, ensuring no moisture enters the case.
- Inspection: Periodically inspect the case for cracks, damage, or loose fittings. A damaged case may compromise the protection of the internal electronics.
- Storage: Store the receiver in a clean, dry environment away from extreme temperatures and direct sunlight.
7. Troubleshooting
- Case Not Closing Properly: Ensure that the receiver's circuit board and any other internal components are seated correctly within the bottom half of the case. Check for any obstructions or misalignments before attempting to close the case halves. Do not force the case closed.
- Physical Damage to Case: If the case becomes cracked or severely damaged, it is recommended to replace it to maintain adequate protection for the receiver's internal components.
8. Specifications
| Model Number | 107A41302A |
| Compatible Receiver | SANWA RX-482 |
| Product Dimensions | 5.91 x 5.91 x 5.91 inches (approximate, as per product data) |
| Item Weight | 2.2 pounds (approximate, as per product data) |
| Material | Plastic |
9. Safety Information
- Always handle electronic components with care to avoid damage from static electricity or physical impact.
- Keep small parts, such as screws or labels, out of reach of children to prevent choking hazards.
- Do not attempt to modify the case or receiver in any way not described in this manual. Unauthorized modifications may void any potential warranty and could lead to malfunction.
10. Warranty and Support
For warranty information or technical support regarding your SANWA RX-482 Receiver Case Set or the RX-482 receiver itself, please refer to the original product documentation that came with your receiver or visit the official SANWA website. Contact information for customer service can typically be found on the manufacturer's website.
