Introduction
This manual provides instructions for the safe and effective use of your Clatronic AT 3605 Alcohol Tester. Please read this manual thoroughly before operating the device and keep it for future reference. This device is designed for personal use as a preliminary indicator of alcohol presence and should not be used as a basis for legal decisions or official measurements.
Important Safety Information
- This device is intended for personal use as a preliminary indicator of alcohol presence. It is not a substitute for official breathalyzer tests or legal evidence.
- Do not operate the device while driving or performing other activities that require full attention.
- Keep out of reach of children.
- Do not expose the device to extreme temperatures, direct sunlight, or moisture.
- Use only the specified battery type (2 x AAA).
- Dispose of batteries and the device according to local regulations.
- Wait at least 20 minutes after consuming alcohol before performing a test to ensure accurate readings.
Product Overview
The Clatronic AT 3605 is a compact alcohol tester designed for personal use. It features a dual LCD display and provides optical warnings at specific alcohol levels.
Device Components
Image 1: Front view of the Clatronic AT 3605 Alcohol Tester. The device features a black face with a white casing. It has two digital LCD screens, one for time (12:00) and another for alcohol test results (e.g., 0.3 g/l and 0.3% BAC). Below the screens are three control buttons: MODE, SET, and ADJ. A larger POWER button is located further down. The Clatronic logo is visible at the bottom.
Controls and Display
- POWER Button: Turns the device on/off.
- MODE Button: Switches between different display modes (e.g., time display, alarm setting).
- SET Button: Confirms selections or enters setting modes.
- ADJ Button: Adjusts values during settings.
- Upper LCD Display: Shows current time (12/24 hour format).
- Lower LCD Display: Shows alcohol test results in g/l and % BAC. Features red backlighting for results and optical warnings.
- Mouthpiece Opening: Located at the top for breath sampling.
Setup
Battery Installation
- Locate the battery compartment cover on the back of the device.
- Slide or open the cover.
- Insert 2 AAA batteries, ensuring correct polarity (+/-).
- Close the battery compartment cover securely.
Note: The device requires 2 AAA batteries. Ensure fresh batteries are used for accurate readings.
Initial Time Setting
Upon first use or after battery replacement, you may need to set the time. Refer to the 'Operating Instructions' for time adjustment.
Operating Instructions
Performing an Alcohol Test
- Press the POWER button to turn on the device. The device will perform a brief self-check.
- Wait for the device to display "WAIT" or a similar indicator, followed by "BLOW" or a countdown.
- When prompted, take a deep breath and blow steadily into the mouthpiece opening for approximately 5 seconds. Ensure a continuous breath sample.
- The device will process the sample and display the results on the lower LCD screen in g/l and % BAC. The display will be red.
- Optical Warning: The device provides an optical warning at 0.2‰ and 0.5‰. If your result is at or above these levels, the display will flash.
- The device will automatically shut off after a period of inactivity to conserve battery life.
Setting Time and Alarm (if applicable)
- With the device on, press the MODE button to cycle through display modes until the time setting mode is reached.
- Press the SET button to enter the time adjustment. The hour digit will flash.
- Use the ADJ button to change the hour.
- Press SET again to move to the minute digit and adjust with ADJ.
- Continue this process for 12/24 hour format or alarm settings if available.
- Press MODE to exit the setting mode.
Maintenance
Cleaning
- Wipe the device exterior with a soft, dry cloth.
- Do not use abrasive cleaners or solvents.
- Do not immerse the device in water or any other liquid.
Storage
- Store the device in a cool, dry place away from direct sunlight.
- If storing for an extended period, remove the batteries to prevent leakage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not turn on. | Dead or incorrectly inserted batteries. | Replace batteries with new AAA batteries, ensuring correct polarity. |
| Inaccurate or inconsistent readings. | Insufficient breath sample; device not calibrated; recent alcohol consumption. | Ensure a strong, continuous breath sample. Wait at least 20 minutes after consuming alcohol before testing. If issues persist, contact customer support. |
| Display shows error message. | Device malfunction or sensor issue. | Turn the device off and on again. If the error persists, contact customer support. |
| Time display is incorrect. | Time not set or batteries removed. | Refer to "Setting Time and Alarm" section to adjust the time. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | AT 3605 (Article Model: 271704) |
| Power Source | 2 x AAA Batteries |
| Measurement Range | 0.0 to 1.9‰ (g/l) / 0.0 to 1.9% BAC |
| Display | 2 Digital LCDs (one with red backlight for results) |
| Special Features | Time display (12/24 hours), Automatic shut-off, Optical warning at 0.2‰ and 0.5‰ |
| Dimensions (L x W x H) | 30L x 40W x 120H mm |
| Material | Plastic |
| Color | Black/White |
Warranty and Support
For warranty information or technical support, please refer to the warranty card included with your product or visit the official Clatronic website. Keep your purchase receipt as proof of purchase. Spare parts availability is typically 1 year from purchase date.
