Notifier LEM-320 Loop Expander Module User Manual

1. Introduction

This manual provides essential information for the proper installation, operation, and maintenance of the Notifier LEM-320 Loop Expander Module. The LEM-320 is designed to expand the capacity of compatible fire alarm control panels by providing additional Signaling Line Circuits (SLCs).

2. Safety Information

Always observe the following safety precautions during installation, operation, and maintenance of the LEM-320 module:

Installation must be performed by qualified personnel in accordance with all local and national electrical codes.
Disconnect all power sources before installing or servicing the module.
Handle electronic components with care to prevent electrostatic discharge (ESD) damage.
Ensure proper grounding to prevent electrical hazards.
Refer to the main fire alarm control panel manual for system-specific safety instructions.

3. Product Overview

The Notifier LEM-320 is a Loop Expander Module designed to interface with a compatible Loop Control Module (LCM-320) to extend the system's capacity for addressable devices. It functions as a daughter board, providing additional even-numbered Signaling Line Circuits (SLCs) to the fire alarm control panel.

Notifier LEM-320 Loop Expander Module, top view

Figure 3.1: Top view of the Notifier LEM-320 Loop Expander Module, showing various integrated circuits and components.

Notifier LEM-320 Loop Expander Module, angled view

Figure 3.2: Angled view of the Notifier LEM-320 module, highlighting the component layout and connection points.

Notifier LEM-320 Loop Expander Module, bottom view

Figure 3.3: Bottom view of the Notifier LEM-320 module, showing the circuit board traces and mounting points.

4. Installation

The LEM-320 module is designed to be mounted as a daughter board onto a compatible Notifier LCM-320 Loop Control Module. Follow these steps for proper installation:

Preparation: Ensure all power to the fire alarm control panel is disconnected. Refer to the LCM-320 manual for specific power-down procedures.
Locate Mounting Position: Identify the designated mounting headers on the LCM-320 board for the LEM-320 daughter board.
Align Module: Carefully align the connectors on the LEM-320 with the corresponding headers on the LCM-320. Ensure correct orientation to prevent damage.
Secure Module: Gently press the LEM-320 into place until it is firmly seated. Use any provided standoffs or screws to secure the module to the LCM-320, if applicable.
Verify Connections: Double-check that all connections are secure and that the module is properly seated.
Power Up: Restore power to the fire alarm control panel according to the manufacturer's instructions.
System Configuration: Configure the fire alarm control panel to recognize the newly installed LEM-320 module and its associated SLCs. Refer to the control panel's programming manual for detailed instructions.

Note: Improper installation can lead to system malfunction or damage. Always consult the specific documentation for the LCM-320 and the main fire alarm control panel.

5. Operation

The Notifier LEM-320 Loop Expander Module operates as an integral part of the fire alarm control panel system. Once properly installed and configured with the LCM-320, it extends the system's capacity by providing additional Signaling Line Circuits (SLCs).

SLC Expansion: The LEM-320 enables the connection of more addressable fire alarm devices (e.g., smoke detectors, heat detectors, manual pull stations, monitor modules) to the system.
Communication: It facilitates communication between the connected SLC devices and the main fire alarm control panel via the LCM-320.
System Integration: The module's operation is fully integrated with the control panel's software, allowing for centralized monitoring and control of all connected devices.

No direct user interaction is typically required with the LEM-320 module itself after initial installation and system configuration. Its function is to provide the necessary hardware expansion for the fire alarm system.

6. Maintenance

The Notifier LEM-320 module is designed for reliable, long-term operation with minimal maintenance. However, periodic inspection and adherence to general electronic component care practices are recommended:

Visual Inspection: Periodically inspect the module for any signs of physical damage, loose connections, or excessive dust accumulation.
Cleaning: If necessary, gently clean the module using a soft, dry, lint-free cloth. Avoid using liquids or abrasive cleaners. Ensure power is disconnected before cleaning.
Environmental Conditions: Ensure the module operates within the specified environmental conditions (temperature, humidity) of the fire alarm control panel enclosure.
System Testing: Regular testing of the entire fire alarm system, including all connected SLC devices, should be performed by qualified technicians as per local codes and manufacturer guidelines.

Caution: Do not attempt to repair the module yourself. Refer all servicing to qualified Notifier service personnel.

7. Troubleshooting

If the fire alarm system experiences issues related to SLC communication or device recognition after the LEM-320 installation, consider the following troubleshooting steps:

Power Check: Verify that the fire alarm control panel has stable power and that the LCM-320 is powered correctly.
Module Seating: Ensure the LEM-320 is securely seated on the LCM-320's connectors. Re-seat the module if necessary (with power disconnected).
Wiring Integrity: Check the wiring of all SLC devices connected to the expanded loops for shorts, opens, or incorrect connections.
System Configuration: Confirm that the fire alarm control panel's programming correctly recognizes the LEM-320 and the expanded SLCs. Verify device addressing.
LED Indicators: Observe any diagnostic LEDs on the LCM-320 or the main control panel for error codes or status indications. Refer to the respective manuals for interpretation.
Consult Manuals: Always refer to the specific troubleshooting sections of the LCM-320 manual and the main fire alarm control panel manual for detailed diagnostic procedures.

If issues persist, contact Notifier technical support or a certified fire alarm technician.

8. Specifications

Feature	Detail
Model Number	LEM-320 (Part Number: NLEM320)
Manufacturer	NOTIFIER
Function	Loop Expander Module for LCM-320
Mounting	Daughter board to LCM-320
Item Weight	2 pounds
Batteries Required	No
Batteries Included	No
Package Quantity	1

9. Warranty and Support

For warranty information regarding the Notifier LEM-320 Loop Expander Module, please refer to the official Notifier warranty statement provided with your product or available on the Notifier website. Warranty terms typically cover defects in materials and workmanship under normal use.

For technical support, service, or to report issues, please contact your authorized Notifier distributor or Notifier technical support directly. Ensure you have your product model number (LEM-320) and any relevant system information ready when contacting support.

Notifier Contact Information:
Please visit the official Notifier website for the most current contact details and support resources. www.notifier.com

	Notifier NFS-320 Intelligent Addressable Fire Alarm System Datasheet Comprehensive datasheet for the Notifier NFS-320 Intelligent Addressable Fire Alarm System, detailing its features, intelligent sensing capabilities, FlashScan protocol, system specifications, compatible devices, and agency approvals.
	Notifier CA-2 Audio Chassis Installation Guide Installation instructions and component details for the Notifier CA-2 Audio Chassis, including preparation, assembly, and field-wiring connection access. Covers mounting of FACP, NCA-2, DVC, microphones, and telephones.
	Notifier AFC-600 Intelligent Addressable Fire Alarm Control Panel with FlashScan® Datasheet Comprehensive datasheet for the Notifier AFC-600 Intelligent Addressable Fire Alarm Control Panel, detailing its features, specifications, system capacity, programming options, compatible devices, and agency approvals. Includes information on FlashScan® protocol and AWACS™™ sensing technology.
	Notifier NRX-M711 Radio System Input/Output Module Installation Instructions Comprehensive installation guide for the Notifier NRX-M711 radio input-output module, detailing its specifications, parts list, wiring, programming, and commissioning for fire alarm systems.
	Notifier LCD-2X20 Series Remote Fire Annunciator Installation and Operations Manual Comprehensive guide for Notifier LCD-2X20 Series Remote Fire Annunciators, covering installation, operation, wiring, programming, and technical specifications for fire alarm systems.
	Notifier NCD Network Control Display: Features and Specifications Explore the Notifier NCD Network Control Display, a next-generation annunciator for the NOTI FIRE NET network. Learn about its advanced features, hardware capabilities, and system integration for fire alarm control.

Notifier LEM-320