Weego 12V DC Adapter (Model JSFSA) Instruction Manual

1. Introduction

The Weego 12V DC Adapter (Model JSFSA) is designed to extend the utility of your Weego jump starter by allowing it to power various 12V DC accessories. This adapter connects to your Weego jump starter via a 5.5mm barrel jack and provides a standard 12V DC (cigarette lighter style) socket output. It is ideal for powering devices such as air compressors, air pumps for inflatables, portable heaters, fans, and lanterns, providing convenient portable power wherever you need it.

2. Product Overview

The Weego 12V DC Adapter consists of a short cable with two primary components:

• 5.5mm Barrel Jack Connector: This end plugs into the compatible output port on your Weego jump starter.
• 12V DC CLA Socket: This end provides a standard automotive-style 12V DC socket, into which you can plug your 12V accessories.

Figure 2.1: The Weego 12V DC Adapter, showing the 5.5mm barrel jack on the left and the 12V CLA socket on the right.

3. Setup

Setting up your Weego 12V DC Adapter is a straightforward process:

1. Ensure Weego is Charged: Before use, ensure your Weego jump starter is adequately charged to provide power to your accessory. Refer to your Weego jump starter's manual for charging instructions.
2. Connect Adapter to Weego: Insert the 5.5mm barrel jack connector of the 12V DC Adapter into the compatible 12V output port on your Weego jump starter. This port is typically labeled "Output 12V".


Figure 3.1: The 5.5mm barrel jack of the adapter connected to the Weego jump starter's output port.

3. Connect Accessory: Plug your 12V DC accessory (e.g., air pump, fan) into the 12V CLA socket of the adapter.


Figure 3.2: A portable air pump plugged into the 12V CLA socket of the adapter, which is connected to a Weego jump starter.

4. Operation

Once the adapter and accessory are connected, you can begin using your 12V device. The Weego jump starter will supply power through the adapter to your accessory.

• Powering Devices: The adapter is suitable for powering various 12V DC accessories, including:
  • Air compressors for tires or inflatables
  • Portable fans
  • Heaters
  • Lanterns and other camping equipment
• Monitoring Power: Pay attention to the power indicator on your Weego jump starter to monitor its battery level during use. Prolonged use of high-drain accessories will deplete the Weego's battery faster.
• Disconnecting: When finished, turn off your accessory, then disconnect it from the adapter, and finally disconnect the adapter from the Weego jump starter.

Figure 4.1: The Weego 12V DC Adapter connected to a Weego jump starter, powering a portable fan.

Figure 4.2: The Weego 12V DC Adapter connected to a Weego jump starter, powering an air compressor to inflate a car tire.

5. Maintenance

The Weego 12V DC Adapter requires minimal maintenance to ensure its longevity and proper function:

• Cleaning: Keep the adapter clean and free from dust, dirt, and moisture. Use a dry, soft cloth to wipe the surfaces. Do not use liquid cleaners.
• Storage: Store the adapter in a cool, dry place when not in use. Avoid extreme temperatures and direct sunlight.
• Inspection: Periodically inspect the cable and connectors for any signs of damage, such as frayed wires or bent pins. If damage is observed, discontinue use and replace the adapter.

6. Troubleshooting

If you encounter issues while using your Weego 12V DC Adapter, consider the following:

• No Power to Accessory:
  • Ensure the Weego jump starter is sufficiently charged.
  • Verify that the 5.5mm barrel jack is fully inserted into the Weego's output port.
  • Check that the 12V accessory is properly plugged into the CLA socket.
  • Some users have reported that the center contact of the barrel jack can be sensitive; try gently wiggling the connector to ensure a secure connection.
  • Test the accessory directly in a known working 12V car socket to rule out an issue with the accessory itself.
• Loose Connection: If the connection feels loose, ensure both the barrel jack and the CLA socket are free of debris that might prevent a firm connection.
• Overheating: If the adapter or your Weego jump starter feels excessively hot, immediately disconnect all devices and allow them to cool down. Ensure the accessory's power draw does not exceed the Weego's output capabilities.

7. Specifications

8. Warranty and Support

For any questions, technical assistance, or warranty information regarding your Weego 12V DC Adapter, please contact Weego customer support. Weego offers lifetime access to their USA-based support team to assist you with your product.

Please refer to the official Weego website or your product packaging for the most current contact information and warranty details.