1. Introduction
This manual provides essential information for the proper installation, use, and maintenance of your ABUS PR 1800 Wall Protection Plate. Please read these instructions carefully before installation to ensure optimal performance and security.
2. Product Overview
The ABUS PR 1800 Wall Protection Plate is designed to enhance the security of your armored lock system by providing a robust barrier against forced entry. It acts as a cover plate, reinforcing the wall area around the lock mechanism.
Figure 2.1: ABUS PR 1800 Wall Protection Plate installed, showing its integration with an armored lock on a brick wall. The plate provides a protective barrier around the lock's bolt.
Key Features:
- Designed for use with ABUS PR 1800 armored locks.
- Provides additional wall protection against tampering and forced entry.
- Durable construction for long-lasting security.
3. Setup and Installation
The ABUS PR 1800 Wall Protection Plate is intended for professional installation or by individuals with appropriate DIY experience. Ensure you have the necessary tools and safety equipment before proceeding.
3.1 Required Tools (Not Included)
- Drill
- Appropriate drill bits for wall material (e.g., masonry, wood)
- Screwdriver
- Measuring tape or ruler
- Pencil
- Level
- Safety glasses
3.2 Installation Steps
- Prepare the Area: Ensure the wall surface where the plate will be installed is clean, dry, and free from obstructions. The plate should be positioned to align perfectly with the existing ABUS PR 1800 armored lock mechanism.
- Position the Plate: Hold the wall protection plate against the wall in its intended final position. Ensure it is level and correctly aligned with the lock's bolt entry point.
- Mark Drilling Points: Using a pencil, mark the locations for the mounting screws through the pre-drilled holes on the plate.
- Drill Pilot Holes: Carefully drill pilot holes at the marked locations. The depth and diameter of the holes should match the specifications of your mounting hardware and wall material.
- Secure the Plate: Place the wall protection plate back over the pilot holes. Insert the appropriate screws (not included, typically supplied with the PR 1800 lock or purchased separately) and tighten them securely. Do not overtighten, as this may damage the plate or the wall.
- Verify Installation: Once secured, check that the plate is firmly attached to the wall and does not wobble. Ensure the armored lock operates smoothly and the bolt extends and retracts without obstruction from the plate.
Figure 3.1: Detail of the ABUS PR 1800 Wall Protection Plate, highlighting its robust construction and mounting points.
4. Operating the Wall Protection Plate
The ABUS PR 1800 Wall Protection Plate is a passive security component. Once correctly installed, it requires no active operation. Its function is to provide continuous physical protection to the wall area surrounding your armored lock, deterring and resisting attempts at forced entry.
Ensure that the armored lock itself is operated according to its own instructions. The wall plate should not interfere with the smooth functioning of the lock.
5. Maintenance
The ABUS PR 1800 Wall Protection Plate requires minimal maintenance to ensure its longevity and effectiveness.
- Cleaning: Periodically wipe the plate with a soft, damp cloth to remove dust and dirt. Avoid abrasive cleaners or solvents, as these may damage the finish.
- Inspection: Regularly inspect the plate for any signs of damage, corrosion, or loosening of screws. If any damage is observed, consider replacing the plate or consulting a security professional.
- Screw Tightness: Check the mounting screws periodically to ensure they remain tight. Retighten if necessary, but do not overtighten.
6. Troubleshooting
As a passive component, the wall protection plate has limited troubleshooting scenarios. Most issues will relate to installation.
| Problem | Possible Cause | Solution |
|---|---|---|
| Plate is loose or wobbly. | Screws are not tightened sufficiently, or pilot holes are too large. | Retighten screws. If holes are too large, use appropriate wall anchors or relocate the plate slightly if possible. |
| Armored lock bolt is obstructed. | Plate is misaligned. | Loosen screws, realign the plate to ensure clear passage for the lock bolt, then retighten. |
| Visible damage to the plate. | Impact or attempted forced entry. | Replace the damaged plate to maintain security integrity. |
7. Specifications
- Model Number: PR 1800
- Brand: ABUS
- Manufacturer: ABUS
- Style: Functional
- Number of Pieces: 1
- ASIN: B01BP4G4DG
- Date First Available: May 20, 2022
- Spare Parts Availability: Information unavailable
8. Warranty and Support
For specific warranty information regarding your ABUS PR 1800 Wall Protection Plate, please refer to the documentation provided with your ABUS armored lock or visit the official ABUS website. Warranty terms may vary by region and product.
For technical support or further assistance, please contact ABUS customer service or visit their official website:
- ABUS Official Website: www.abus.com
- ABUS Store on Amazon: Visit ABUS Store
