Chauvet DJ FC-W Wireless Remote Fog Machine Controller Instruction Manual

1. Introduction

This manual provides detailed instructions for the safe and effective operation of the Chauvet DJ FC-W Wireless Remote Fog Machine Controller. Please read this manual thoroughly before use to ensure proper setup, operation, and maintenance.

The FC-W is designed to provide wireless control over compatible Chauvet fog machines, offering convenience and flexibility in various event settings. It features a receiver unit that connects to the fog machine and a handheld transmitter for remote activation.

2. Safety Information

Always observe the following safety precautions to reduce the risk of fire, electric shock, or injury:

• Ensure the fog machine is unplugged from the power source before connecting or disconnecting the FC-W receiver.
• Do not expose the FC-W components to rain or moisture.
• Do not operate the unit if the power cord or receiver is damaged.
• Refer all servicing to qualified service personnel.
• Use only with compatible Chauvet fog machines as specified in this manual.

3. Package Contents

Verify that all components are present upon opening the package:

• FC-W Receiver Unit
• FC-W Transmitter (Remote)
• User Manual (this document)

Figure 1: FC-W Wireless Remote Fog Machine Controller showing the receiver unit, its connecting cable, and the handheld remote transmitter.

4. Setup

4.1 Compatibility

The FC-W Wireless Remote is compatible with the following Chauvet Hurricane fog machines:

• Hurricane H-900
• Hurricane H-1100
• Hurricane H-1300
• Most other CHAUVET fog machines with a compatible 5-pin remote input.

4.2 Connecting the Receiver

1. Ensure your fog machine is powered off and unplugged from the main power supply.
2. Locate the remote control input port on your Chauvet fog machine. This is typically a 5-pin DIN connector.
3. Connect the cable from the FC-W receiver unit into the remote control input port of the fog machine. Ensure a secure connection.
4. The FC-W receiver unit receives power directly from the fog machine, eliminating the need for an external power adapter.
5. The receiver unit features a magnetized back plate, allowing it to be conveniently attached to the metal casing of the fog machine or other magnetic surfaces.

4.3 Setting DIP Switches (for multiple units)

The FC-W system supports controlling up to four fog machines independently. To achieve this, each receiver unit must be assigned a unique address using its DIP switches.

1. On the FC-W receiver unit, locate the small DIP switch bank.
2. Use a small tool (like a pen tip) to set the switches according to the desired address (1-4). Refer to the table below for common settings.
3. Ensure the handheld transmitter is also set to the corresponding address to control that specific fog machine.

Note: The DIP switch settings shown in the image (red switches) indicate a specific configuration. Always refer to the table for correct addressing.

5. Operating Instructions

5.1 Initial Power-Up

1. After connecting the FC-W receiver to the fog machine, plug the fog machine into a suitable power outlet.
2. Allow the fog machine to warm up. The FC-W receiver unit has two LED indicators:
   • A red LED indicates the fog machine is heating.
   • A green LED indicates the fog machine is ready for operation.

5.2 Wireless Fog Output

1. Once the green LED on the receiver unit illuminates, the fog machine is ready.
2. Press and hold the button on the handheld FC-W transmitter to activate fog output. Release the button to stop fog output.
3. The unobstructed operating distance for the wireless remote is approximately 100 feet (30 meters). Performance may vary depending on environmental factors and obstructions.
4. If controlling multiple fog machines, ensure the transmitter is set to the correct address for the desired machine.

5.3 Transmitter Battery Replacement

The handheld transmitter is powered by a small battery. If the range decreases or the unit becomes unresponsive, the battery may need replacement. Refer to the transmitter's casing for battery type and replacement instructions.

6. Maintenance

The Chauvet DJ FC-W Wireless Remote requires minimal maintenance. Follow these guidelines to ensure longevity:

• Cleaning: Wipe the exterior of the receiver and transmitter with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Storage: Store the unit in a cool, dry place away from direct sunlight and extreme temperatures when not in use.
• Inspection: Periodically inspect the cable and connectors for any signs of wear or damage. If damage is found, discontinue use and contact qualified service personnel.

7. Troubleshooting

8. Specifications

9. Warranty Information

Chauvet DJ products are covered by a limited warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Chauvet DJ website. Keep your proof of purchase for warranty claims.

10. Customer Support

For technical assistance, service, or parts, please contact Chauvet DJ customer support. Before contacting support, please have your product model number (FC-W) and ASIN (B01BHSEM16) ready.

Chauvet DJ Official Website: www.chauvetdj.com

Note: Support contact methods (phone, email) may vary by region. Please check the official website for the most current contact information.